mori seiki ZL-153 Скачать руководство пользователя страница 491

Страница: 491 / 561

PREPARATION BEFORE STARTING MASS PRODUCTION F-7

CHECKING A PROGRAM USING MACHINE LOCK FUNCTION

This section describes the procedure used for checking the program stored in the NC by

displaying the list of the program on the screen while executing it using the machine lock function.

Since the program is executed in the machine lock status, the axes do not move but only the

position data on the screen is updated as the program is executed.

When using the NC functions, refer to page A-26 (5-6) to find the details of them.

Carry out the procedure explained in 4-1

"Preparations for Checking a Program".

Place the DOOR INTERLOCK key-switch in the

NORMAL

position.

Close the front door.

Place the PANEL key-switch in the

(ON)

position.

Press the HEAD CHANGE switch

(head 1) or

(head 2) to select the required turret.

Carry out the zero return operation.

NOTE

PANEL
/EDIT

OFF

PANEL

HEAD CHANGE

MODE

MEM

MDI

TAPE

EDIT

JOG

RPD

ZRN

Содержание ZL-153


















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды

mori seiki ZL-153, Руководство по эксплуатации

Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды