mori seiki ZL-153 Скачать руководство пользователя страница 469

Страница: 469 / 561

SETTING OF COORDINATE SYSTEM E-43

9-3

Installing and Removing the Presetter Arm

To use the in-machine tool presetter, install the presetter arm to the machine and measure the tool

geometry offset data. After completing measurement, remove the presetter arm from the

machine.

This section describes the procedure for installing and removing the presetter arm.

Never attempt mounting/removal of the presetter arm in the presetter mode (the

indicator in the presetter mode switch

is lit). If attempted, the tool geometry

offset data could be changed depending on the contact conditions of the

connection part at the base and the presetter arm. If machining is executed

although the tool geometry offset data has been changed, it will cause

interference of the tools, tool holders, and/or turret head with the workpiece,

chuck, and/or fixture, causing damage to the machine.

When installing the presetter arm to the machine or removing it from the machine

or container, pay sufficient care not to give shocks to the presetter arm, especially

to the sensor. If shocks are applied to the sensor or presetter arm, the sensor

may be damaged or the presetter arm may be distorted, making it impossible to

set the appropriate tool geometry offset data.

<Installing the presetter arm>

Clean the area around the base so that chips and

foreign matter will not stick on the base and the

removed cover. Also keep them away from coolant.

Turn the locking lever counterclockwise to the

unlock position (angle of turning: 132

Remove the protection cover from the base.

Take out the presetter arm from the container.

When taking out the presetter arm, make sure to

hold the grip of it.

Do not hold the presetter arm for a long time.

Make sure that the connection parts of the presetter

arm and the base are free of chips and foreign

matter.

When cleaning the base with rag, pay attention

so that chips and foreign matter will not enter

the hole in the lock mechanism. Entry of

foreign matter will cause malfunctioning of the

tool presetter.

If the connection part is dirty with chips or foreign

matter, clean the connection part with rag.

CAUTION

Sensor

Stylus

Locking lever

Base for turret 1

Positioning pin

Grip

Protection cover

Base for turret 2

NOTE

Alignment mark

CAUTION

NOTE

Содержание ZL-153


















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды

mori seiki ZL-153, Руководство по эксплуатации

Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды