mori seiki ZL-153 Скачать руководство пользователя страница 283

Страница: 283 / 561

MANUAL OPERATION B-55

12-6

Adjusting the Tailstock Spindle Stroke

The tailstock spindle retract end position can be adjusted.

Place the DOOR INTERLOCK key-switch in the

NORMAL

position.

With the manual door type machine, press the

DOOR UNLOCK switch

to unlock the front

door. Then open the front door.

With the automatic door type machine, open the

front door by pressing the AUTOMATIC DOOR

OPEN switch.

Press the

(TSINC) switch to move the tailstock

spindle out to the proper position.

Turn the piston stroke adjustment bolt

counterclockwise to loosen it.

Press the

(TSI) switch.

The tailstock spindle moves in the tailstock body.

DOOR INTERLOCK

NORMAL

RELEASE

DOOR UNLOCK

NOTE

TAILSTOCK

TSO

TSINC

TSI

TAILSTOCK

TSO

TSINC

TSI

Содержание ZL-153


















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды

mori seiki ZL-153, Руководство по эксплуатации

Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды