manualshive.com logo in svg

mori seiki NZ-S1500, Руководство по эксплуатации

Поделиться
Скачать
mori seiki NZ-S1500 Скачать руководство пользователя страница 46

PREFACE

This manual provides the information necessary to operate the machine.  Information explained in 
each chapter is briefly described below.

DOOR INTERLOCK FUNCTION

The door interlock function is provided to ensure the operator's safety.
This chapter deals with the purpose and specifications of the door interlock function.
Before operating the machine, read this chapter carefully.

A: OPERATION PANELS

Switches used to turn on/off the power supply, the functions and operational procedure of the 
switches and keys on the operation panel are explained.

B: MANUAL OPERATION

The procedure used to turn on/off the power supply, and to stop the machine in emergency 
cases are described.

This chapter also provides the procedure to feed the axes or to start/stop the spindle 
manually.

C: CHUCKING

This chapter explains the cautions for chucking a workpiece and the procedure for adjusting 
the chucking pressure.

The soft jaw shaping procedure is also explained.

D: SETTING OF COORDINATE SYSTEM

This chapter explains the coordinate system used in creating programs and machining 
workpieces.
There are two kinds of coordinate system settings as follows:

•

The coordinate system set using the tool geometry offset function
(G00 T_;)

•

The work coordinate system (G54 to G59)

E: PREPARATION BEFORE STARTING MASS PRODUCTION

This chapter explains the procedures for checking a program and finishing a workpiece within 
the specified tolerance before starting mass production.  The checkups before starting mass 
production are also explained.

Содержание NZ-S1500





































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды