mori seiki NZ-S1500 страница 199 Скачать руководство пользователя

Страница: 199 / 324

B-48 MANUAL OPERATION

12-4

Spindle Clamp/Unclamp Operation

The spindle can be clamped and unclamped manually.

In the following conditions, the spindle clamp/unclamp operation cannot be performed.

The spindle is rotating or the C-axis is being indexed.

The machine is in the spindle and rotary tool spindle simultaneous operation mode.

Place the DOOR INTERLOCK key-switch in the

NORMAL

position.

Close the front door.

Place the PANEL key-switch in one of the positions
indicated below.

(ON)

(PANEL/EDIT)

Select any of the following modes with the MODE
selection switch.

(H)

(JOG)

(RPD)

(ZRN)

Clamp or unclamp the spindle.

<Clamp>

Press the

(CL) switch.

The spindle is clamped.
The indicator in the switch is lit.

<Unclamp>

Press the

(UCL) switch.

The spindle is unclamped.
The indicator in the switch is lit.

NOTE

DOOR INTERLOCK

NORMAL

RELEASE

PANEL
/EDIT

OFF

PANEL

MEM

MDI

TAPE

EDIT

JOG

RPD

ZRN

MILLING

UCL

MIL

MILLING

UCL

MIL

Содержание NZ-S1500





































































































































































































































































































































Результаты поиска

Содержание NZ-S1500

Отзывы:

Похожие инструкции для NZ-S1500

Бренды по названию

Популярные бренды

mori seiki NZ-S1500, Руководство по эксплуатации

Результаты поиска

Содержание NZ-S1500

Отзывы:

Похожие инструкции для NZ-S1500

Бренды по названию

Популярные бренды