Moons' SSM24C Скачать руководство пользователя

Страница: 42 / 50

Rev. 1.0

0006302011

SSM24C User Manual

+86-400-820-9661

6.6 Drive Status

The

Drive Status

is an overall indication of the drive condition. In a typical application this is

the most common information that should be collected from the drive. Collecting the drive status

information allows the system controller to keep track of drive operations and conditions.

Drive Status
Enabled

the drive is enabled and ready for moving operations

Tuning

the drive is in the process of tuning data capture

Fault

an alarm fault condition has occured (check Alarm Status)

InPosition

command position is within the PL (Position Limit) range

Moving

a commanded move is in process

Jogging

commanded jogging is in process

Stopping

the motor is decelerating

WaitInput

a WI (Wait on Input) command is executing

Saving

drive is saving parameter data

Alarm

an Alarm Code is present

Homing

the SH (Seek Home) command is executing

Delay

a WT (Wait Time) command is executing

Q Programing

does not apply to an S model

Initializing

the drive is in the process of power-up initialization

Содержание SSM24C



















































Результаты поиска

Содержание SSM24C

Отзывы:

Похожие инструкции для SSM24C

Бренды по названию

Популярные бренды

Moons' SSM24C, Руководство пользователя

Результаты поиска

Содержание SSM24C

Отзывы:

Похожие инструкции для SSM24C

Бренды по названию

Популярные бренды