background image

R320 & R420  Power Vent Indoor gas Fireplace

Page 35

XG0770 - 100614

Appendix

PVHEX58-300 Power Vent Locations

v

v

FIXED

CLOS

ED

OPERA

BLE

F

C

B

v

v

OPERA

BLE

FIXED

CLOS

ED

v

B

X

B

A

B

J

H

I

X

K

v

M

V

B

L

D

E

V

INSIDE

CORNE

R DET

AIL

v

G

A

V

VENTER TERMINAL

X

AIR SUPPLY INLET

AREA WHERE TERMINAL IS

NOT PERMITTED

PVHEX58-300

A= Clearance above grade, veranda,

porch, deck, or balcony

12 in (30 cm)

12 in (30 cm)

Canadian Installations

US Installations

1

2

B= Clearance to window or door that
may be opened

6 in (15 cm) for appliances <

10,000 Btuh (3 kW), 12 in
(30 cm) for appliances >
10,000 Btuh (3 kW) and <
100,000 Btuh (30 kW), 36 in
(91 cm) for appliances >
100,000 Btuh (30 kW)

6 in (15 cm) for appliances <

10,000 Btuh (3 kW), 9 in
(23 cm) for appliances >
10,000 Btuh (3 kW) and <

50,000 Btuh (15 kW), 12 in
(30 cm) for appliances >
50,000 Btuh (15 kW)

C= Clearance to permently closed
window

B

B

6 in (15 cm)

D= Vertical clearance to ventilated
soffit located above the terminal within
a horizontal distance of 2 feet (61 cm)

from the center line of the terminal

6 in (15 cm)

E= Clearance to unventilated soffit

6 in (15 cm)

6 in (15 cm)

F= Clearance to outside corner

6 in (15 cm)

6 in (15 cm)

G= Clearance to inside corner

6 in (15 cm)

6 in (15 cm)

H= Clearance to each side of center
line extended above meter/regulator
assembly

3 ft (91 cm) within a height 15
ft. (4.5 m) above the meter/
regulator assembly

*

I= Clearance to service regulator

vent outlet

3 ft (91 cm)

*

J= Clearance to nonmechanical air
supply inlet to building or the
combustion air inlet to any other
appliance

6in (15 cm) for appliances <

10,000 Btuh (3 kW), 12 in (30

cm) for appliances > 10,000
Btuh (3 kW) and < 100,000
Btuh (30 kW), 36 in (91 cm)
for appliances > 100,000
Btuh (30 kW)

Canadian Installations

US Installations

1

2

6in (15 cm) for appliances <

10,000 Btuh (3 kW), 9 in (23

cm) for appliances > 10,000
Btuh (3 kW) and < 50,000
Btuh (15 kW), 12 in (30 cm)
for appliances > 50,000 Btuh
(15 kW)

K= Clearance to a mechanical air
supply inlet

6 ft (1.83 m)

3 ft (91 cm) above if within 10
ft (3 m) horizontally

L= Clearance above paved sidewalk
or paved driveway located on
public property

7 ft (2.13 m)

*

M= Clearance under veranda porch
deck, or balcony

12 in (30 cm)

*

1    In accordance with the current CSA B149.1, Natural Gas and Propane Installation Code

2    In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code
      A vent shall not terminate directly above a sidewalk or paved driveway that is located between two
      single family dwellings and serves both dwellings.
      Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath
      the floor.
*     For clearances not specified in ANSI Z223.1/NFPA or CSA B149.1, one of the following shall be
      indicated
a)   A minimum clearance value determined by testing in accordance with section 2.23.5, or;
b)   A reference to the following footnote:
      "Clearance in accordance with local installation codes and the requirements of the gas supplier"

Figure 25b.

  PVHEX58-300 Power Vent Locations

Содержание R320











































Отзывы: