Montigo R320 страница 3 Скачать руководство пользователя

Страница: 3 / 42

Congratulations on your purchase of a

Montigo Fireplace

With over 30 years of experience, Montigo is committed to providing

you with a gas fireplace that is not only a beautiful addition to your

space, but that is also designed and manufactured to the highest

safety, reliability and engineering standards.

We strongly encourage you to read and carefully follow the instructions

laid out in this Installation, Operation and Maintenance Manual

and retain it for your future reference. Pay special attention to all

cautions, warnings, and notices throughout this manual intended

to ensure your safety.
This manual covers installation, operation and maintenance. Lighting,

operation and care of this fireplace can be easily performed by the

homeowner. All installation and service work should be performed

by a qualified or licensed installer, plumber or gas fitter as certified

by the state, province, region or governing body where the fireplace

is being installed.
This installation, operation and maintenance manual is applicable

to the models described below. Refer to your rating plate to verify

included options.

Warranty and Installation Information: (See Appendix B)

The Montigo warranty will be voided by, and Montigo disclaims any

responsibility for, the following actions:

► Modification of the fireplace and/or components including

Direct-Vent assembly or glass doors.

► Use of any component part not manufactured or approved

by Montigo in combination with this Montigo fireplace system.

► Installation other than as instructed in this manual.

Consult your local Gas Inspection Branch on installation requirements

for factory-built gas fireplaces. Installation & repairs should be

done by a qualified contractor.

R320N-I

50,000

R320L-I

40,000

R420N-I

65,000

R420L-I

55,000

WARNINg

Hot glass

will cause

burns.

Do not touch

glass until unit is cooled.

Never

allow children to

touch glass.

Irritant

Cutting

Watch your step

Slippery floor

High temperatures

Glass hazard

Danger of suffocation

High voltage

Toxic

Flammable materials

Corrosive

Fork lift trucks

Danger overhead crane

Explosion risk

Oxidising

Danger of death

Biohazard

Laser Radiation

Danger of entrapment

Hot surface

General Warning

Blank

Gas bottles

Watch for

falling objects

Electricity

Danger for cutter

Entrapment hazard

Battery hazard

Rotating parts

Low temperature

Strong magnetic field

Optical radiation

Non ionizing

radiation

Radiation

Hazardous to the

Environment

Danger of harming

your hands

MODEL

Natural

gas

Liquid Propane

gas Rating (BTU hr)

Linear

Burner w/

glass

Accessories

Honeywell Hot Surface Ignition

Page 3

XG0770 - 100614

R320 & R420 Power Vent Indoor Gas Fireplace

Safety Alert Key

Safety Alerts

Introduction

Содержание R320











































Результаты поиска

Содержание R320

Отзывы:

Похожие инструкции для R320

Бренды по названию

Популярные бренды

Montigo R320, Инструкция по установке и обслуживанию

Результаты поиска

Содержание R320

Отзывы:

Похожие инструкции для R320

Бренды по названию

Популярные бренды