Page 18
Divine Outdoor Gas Fireplace
XG0150 - 140707.2
Operation
Section 9: Start-up Sequence with Continuous Pilot
To Turn Off Gas To Appliance:
1. Turn fireplace off using wall switch or remote control.
2. Locate the gas control behind the lower trim, or on the
rear left side (on Cast stoves).
3. Push in gas control knob slightly and turn
clockwise to "Off". Do not force.
4. Turn incoming gas control valve to off
with American Flame Electronic Ignition
For Your Safety - READ BEFORE LIGHTING:
Lighting Instructions:
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it. Call a qualified service
technician. Force or attempt to repair may result in a fire
or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system, and any gas control which has been
under water.
A. This appliance has a pilot which must be lit by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
What To Do If You Smell Gas:
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any phone
in your building.
•
Immediately call your gas supplier from a neighbour's
phone. Follow the gas supplier's instructions.
•
If you cannot reach your gas supplier, call the Fire
Department.
1. STOP! Read the safety information above on this label.
2. Locate the gas control behind the lower trim, or on the
rear left side (on Cast stoves).
3. Push in gas control knob and turn clockwise
to
"OFF."
4. Wait five (5) minutes to clear out any gas. Smell for gas,
including near the floor. If you smell gas, STOP! Follow "B"
in the safety information above on this label. If you don't
smell gas, go to the next step.
5. Locate pilot burner (See illustrations and follow steps
below.
6. Turn knob on gas control counter clockwise
to
"PILOT."
7. Push in gas control knob completely and hold. Light with
Piezo Igniter button. Continue to hold the control knob in
for about (1) minute after the pilot is lit. Release the knob
and it will pop back up. Pilot should remain lit. If it goes
out repeat steps 3 through 7.
•
If knob does not pop up when
released, STOP! Immediately call
your service technician or gas
supplier.
•
If the pilot will not stay lit after
several tries, turn the gas control
knob to "OFF" and call your
service technician or gas supplier.
8. Push in gas control knob and turn counter clockwise
to "ON."
9. Turn on remote switch to ignite fire.
WARNING/ CAUTION: Hot while in operation. Do not touch. Severe burns
may result. Keep children, clothing, furniture, gasoline and other liquids
having flammable vapours away.
See installation and operating instructions accompanying this appliance.
If the information in these instructions is not followed exactly, a
fire or explosion may result causing property damage, personal
injury or death.
WARNING
P/N LB1
169-1
1/2017
NOTE: Knob cannot be turned
from "PILOT" to "OFF" unless
knob is pushed in slightly. Do
not force.
HI- LO
Robert Shaw Valve
SIT 820 HI/LO Valve
Typical pilot shown, see
instruction manual for
pilot specific to your
model.
To Turn off Gas To appliance:
liGhTinG insTrucTions:
for Your safeTY - read Before liGhTinG:
A. This appliance has a pilot which is lit automatically. Do
not attempt to light the pilot by hand.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
What To Do If You Smell Gas:
■
Do not try to light the appliance.
■
Do not touch any electrical switch. Do not use any
phone in your building.
■
Immediately call your gas supplier from a
neighbour's phone. Follow the gas suppliers
instructions.
1. STOP! Read the safety information above on this label.
2. Turn the fireplace "OFF" using the wall switch or remote
control.
3. Wait 5 minutes to clear out any gas. If you smell gas,
STOP! Follow "B" in the safety information above on
this label. If you don't smell gas, go to the next step.
4. Turn the fireplace "ON" using the wall switch or remote
control.
NOTE: This unit is equipped with an ignition system
that lights the pilot burner automatically. Do not
attempt to light the pilot by hand.
This unit is equipped with advanced safety
controls including pre and post purge timers.
The fireplace will not turn on until all of the
safety conditions are met. The fans in the
fireplace may operate for an extended period of
time even after the wall switch is turned off.
■
If you cannot reach your gas supplier, call the Fire
Department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or turn
by hand, don't try to repair it. Call a qualified service
technician. Force or attempt to repair may result in a fire
or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system, and any gas control which has been
under water.
1. Turn the fireplace off using the wall switch or remote
control.
2. Turn off all electrical power to the appliance.
3. Locate the gas shut off valve for the appliance and
P/N
LB1
170-050514
WarninG if the information in these instructions are not followed
exactly, a fire or explosion may result causing property damage,
personal injury or death.
WarninG / cauTion: hot while in operation. do not touch.
severe burns may result. Keep children, clothing, furniture,
gasoline and other liquids having flammable vapors away.
see installation and operating instructions accompanying this appliance.
5. The wall switch LED and heat sensor LED will light up.
6. Once the predetermined airflow is established in the
firebox, the flue gas switch LED will light up after 30
seconds.
7. After approximately 1 minute the hot surface igniter will
start to glow. The pilot will light up, followed by the main
burner. The fireplace will then start up.
NOTE: If the igniter does not glow, even after 3 minutes
have passed, follow the instructions "To Turn Off
Gas To Appliance" and call your service
technician or Montigo dealer.
Control box LED lights
turn off.
Heat Sensor /
Conmustion Air
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and must be installed for the protection
of children and other at-risk individuals.
HOT GLASS
WILL CAUSE BURNS.
DO NOT TOUCH
GLASS UNTIL
COOLED.
NEVER
ALLOW CHILDREN
TO TOUCH GLASS.
DANGER
