Montesa COTA 300RR 2018 Скачать руководство пользователя страница 70

Страница: 70 / 176

Engine servicing

4-7

(1) 2P CONNECTOR

(2) SOCKET BOLTS

(1) BREATHER HOSE

(2) BOLT

(3) FUEL TANK

(1) 2P CONNECTOR

Fuel Tank/Fuel Pump

Removal

Remove the rear fender.

Disconnect the injector 2P connector.

Remove the injector holder socket bolts.

Disconnect the fuel tank breather hose.

Remove the fuel tank mounting bolts.

Pull up the fuel tank and disconnect the fuel pump 2P

connector.

Remove the fuel tank and injector as an assembly being

careful not to damage the injector especially tip of the

injector.

After removing the fuel tank/injector assembly, protect tip

of the injector.

Also cover the cylinder head injector hole to prevent dust

and dirt fall into the combustion chamber.

Содержание COTA 300RR 2018

















































































































































































Результаты поиска

Содержание COTA 300RR 2018

Отзывы:

Бренды по названию

Популярные бренды

Montesa COTA 300RR 2018, Руководство пользователя

Результаты поиска

Содержание COTA 300RR 2018

Отзывы:

Бренды по названию

Популярные бренды