manualshive.com logo in svg

Montesa COTA 300RR 2018, Руководство пользователя

Поделиться
Скачать
Montesa COTA 300RR 2018 Скачать руководство пользователя страница 119

Engine servicing

4-56

4-56

(1) LEFT CRANKCASE

Crankcase Bearing Replacement

Remove the oil seals and bearing set plates.

Drive out the bearing using the special tools (Tools; page 

2-7).

Install the new bearing as shown in the illustration using 

the special tools.

(1) RIGHT CRANKCASE

(1) RIGHT SHIFT FORK   

(2) LEFT SHIFT FORK

(3) RIGHT/LEFT SHIFT FORK SHAFT

(4) CENTER SHIFT FORK/SHAFT   

(5) SHIFT DRUM

Inspect each part for wear or damage.

Check the following items (specifications; page 2-1).

 

Spinning gear I.D.

 

Bushing I.D. and O.D.

 

Mainshaft and countershaft O.D.

 

Shift fork I.D. and claw thickness

 

Shift fork shaft O.D.

 

Shift drum O.D.

Crankshaft/Transmission Inspection

Measure the crankshaft runout.

Support the crankshaft at point “A” and “B”, and then 

measure the runout at the points “C” and “D”.

Service limit: 

C:  

0.05 mm (0.002 in)

 

D:  

0.03 mm (0.001 in)

Measure the connecting rod big end side clearance and 

big end axial/radial play (specification; page 2-3).

8 mm

A

6 mm

B

C

D

1

5

4

3

2

1

1

Содержание COTA 300RR 2018

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды