background image

5

© 2013 Monte Carlo Fan Company

11/15/2012

13

14

15

16

17

18

Install ball end of downrod into mounting 

bracket opening. Align (engage) slot on 

ball with tab on mounting bracket.

Warning:

 Failure to align slot on ball with 

tab may result in serious injury.

Set dip switches on the Remote 

Transmitter and Remote Receiver to the 

same settings. This must be done so the 

units will communicate properly. If you 

have other fans you can set to control 

from one Transmitter by setting  

receivers the same as the Transmitter. If 

you have more than one fan with remote, 

you can set the dip switches to different 

positions to have separate control

Make wiring connections using wire 

connectors provided as indicated above.  

White from fan to White from remote 

marked N. Black from fan to Black from 

remote marked L. White from house to 

White from remote marked AC N. Black 

from house to Black from remote marked 

AC L. Connect all green grounded wires 

to Grounded wire from House. Make sure 

that no filaments are outside of the wire 

connectors.

Insert the remote receiver into mounting 

bracket. 

Loosen one and remove one 

preassembled screw from mounting 

bracket. Save screw. 

 

Lift canopy up, aligning its keyhole slot 

with the preassembled screw on 

mounting bracket and twist 

counterclockwise to lock in place. 

Reinstall the screw removed in step 17 

and tighten all screws securely. 

For Canadian installation and for USA fan 

and light kit combinations over 35 lbs, in 

both flush and downrod modes the safety 

cable must be installed into the house 

structure beams using 3” lag screws, 

washers and lock washers provided. 

Make sure that when the safety cable is 

fully extended the lead wires are longer 

than the cable and no stress is placed on 

the lead wires.

Note

: If Installing The Secondary Support 

Safety Cable in the U.S., Do Not Remove 
Knockouts In The Outlet Box.

 

17

Tab

Downrod

Slot

13

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

ON

Dip switches

Wall switch

Black

White

Ground/Green

Ground/Green

White

White

Black

Black

Receiver

Mounting bracket

Canopy

Содержание 3ELR44 Series










Отзывы: