Montag C06B Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 33

Montag C06B Скачать руководство пользователя страница 28

28

6.4 SERVICE HUB BEARINGS AND SEALS

Note: Perform this service every three years or 5000 acres of use, whichever comes first.

Prevent death or serious injury.

Cart assembly weighs up to 13140 lbs (5960 kg) depending on configuration.

Tire/wheel assembly weighs approximately 820 lbs (372 kg).

Spindle assembly weighs approximately 360 lbs (163 kg).

Use adequate lifting and support devices.

Crushing hazard.

Before performing inspections, service or maintenance:

•

Park the equipment on firm, level surface.

•

Place tractor transmission in park, turn tractor engine off and remove ignition key

and place do not operate tag on ignition switch.

• Do not disconnect cart from implement for servicing.

• Block the wheels.

• Lower all equipment to the ground or pavement.

1.

Remove all product from tank.

2.

Raise and support cart using adequate lifting and support devices.

3.

Remove wheel using an adequate lifting device.

4.

Remove 4 bolts (A), remove hub cap (B) and seal (C). Discard seal.

5.

Remove cotter pin (D), slotted nut (E), washer (F) and outer bearing (G).

6.

Remove hub (H) from spindle.

7.

Remove seal (I) and inner bearing (J) from hub. Discard seal.

8.

Clean and inspect bearings, bearing cups (K), hub and spindle.

I

J

K

K

G

F

E

C

B

A

D

H

«
...
26
27
28
29
30
...
»

Содержание C06B


































Отзывы:

Нет отзывов