SmartSELECT Merchant Operating Manual v 2.0
35
Configuring Your Terminal
4.9: 3201 Direct Communications Parameters
If your terminal will being communicating with the Moneris Host over a Datapac
3201 direct line, you will need to set up this parameter.
1. Press
Menu
. The
Financial Transactions
menu appears.
2. Press
Config
. The
Terminal Configuration
menu appears.
3. Select
General Parameters
. The
General Parameters
menu appears.
4. Ensure that 3201 is selected as the communications type.
5. Select
3201 Poll Code
. The
Enter Datapac 3201 Poll Code
prompt appears.
6. Key in the 2-character poll code and press
Enter
to return to the
General
Parameters
menu.
7. Press
Exit
to return to the
Terminal Configuration
menu.
8. Press
Exit
. The Idle screen appears.
The terminal is once again ready to communicate with the Moneris Host.
4.10:LAN Communication Parameters
You must set up one SmartSELECT terminal in the LAN as a LAN Master station
and the remaining terminals in the LAN as LAN slaves in order to allow the termi-
nals to communicate with the Moneris Host over a 3201-based LAN connection.
4.10.1: Configure Terminal as LAN master station
From the Idle screen:
1. Press
Menu
. The
Financial Transactions
menu appears.
2. Press
Config
. The
Terminal Configuration
menu appears.
3. Select
General Parameters
. The
General Parameters
menu appears.
4. Ensure that LAN is selected as the communications type:
a. Select
Communications Type
. The
Communications Type
menu
appears.
b. Select
LAN
. The
General Parameters
menu reappears.
c. Press
Exit
. The
Terminal Configuration
menu reappears.
5. To identify this terminal as the master terminal:
a. Select
LAN Master Terminal
. The
Testing LAN for Activity
prompt appears
while the terminal checks the LAN port for activity.
•
If the port is active, the
LAN Master Station?
prompt appears.
•
If there is no activity on the port, the
No Poll Received
message
appears on the screen, then the
General Parameters
menu reappears.
Note:
Check that the communication cable is connected to the correct port on
the SmartSELECT terminal and try the configuration again.
b. Select
Yes
to set this terminal as the Master terminal. The LAN Address
parameter is automatically set to “20” and the prompt
Please Wait
appears
while the terminal checks for the eN-LAN 2000 version.
c. When the terminal receives the eN-LAN 2000 version number, it displays
the version number on the screen,
eN-LAN 2000 Ver. #.##
, for three sec-
onds then the
General Parameters
menu reappears.
Содержание smartselect
