Page 11
5.4.4
FAIL SAFE -
Press the
SET
button and use the
UP
button to select whether the Alarm is FAIL
Safe – select
YES
, or
NO
. Press the
SET
button to select the new setting or the
RECALL
button to
exit without saving the settings.
5.4.5
SET POINT -
Press the
SET
button to display the current SET POINT value and use the buttons
to set the required value. Press
RECALL
to exit up one level without making a change or press
SET
to save the change. The edit buttons function as follows:
RESET
- changes the digit being edited (blinking digit)
UP
- increases the digit by 1
DOWN
- decreases the digit by 1
RESET
+
- shifts the decimal point
RECALL
- aborts the edit process
SET
- saves data and exits
5.4.6
DEAD BAND -
Press the
SET
button to display the current DEAD BAND value and use the
buttons to set the required value. Press
RECALL
to exit up one level without making a change or
press
SET
to save the change. Edit the value using the buttons as shown in
above.
5.5
Same as
but for
ALARM 2
.
5.6
Used to set or show the Analog Output (Option) parameters. This menu item has a number of sub items. Once selected
with the
SET
button, the instrument will display its current setting. To exit back to the main menu without changing the
function, press the
RECALL
button. If you wish to change the function, you can view the options using the
UP
button.
The available options are shown below. When the desired function is displayed, press the
SET
button. The unit will return
to the last menu level.
5.6.1
ZERO SCALE -
Sets the Zero Scale value for the Analog output. Press the
SET
button and use
the buttons to edit the value as per
above. Press
RECALL
to exit up one level without
making a change or press
SET
to save the change.
5.6.2
FULL SCALE -
Sets the Full Scale value for the Analog output. Press the
SET
button and use the
buttons to edit the value as per
above. Press
RECALL
to exit up one level without making a
change or press
SET
to save the change.
5.6.3
DIAGNOSTIC -
Sets the analog output to a preset value for diagnostic purposes. Options are
,
or
(Zero) scale. Press
RECALL
to exit up one level without making a change or
press
SET
to save the change.
5.7
Sets the BAUD rate for serial communication (Option). Press the
SET
button to display the current baud rate. Press the
UP
button to view the baud rate options:
.
- 115200,
.
- 57600,
.
- 38400,
.
- 19200,
.
- 9600,
.
- 4800,
.
– 2400. When the desired mode is displayed, press the
SET
button to select or the
RECALL
button to ignore. The unit
will return to the menu.
5.8
Sets the IP Address for the
Ethernet
interface (Option). There are three sub items:
– IP Address,
– Sub Net Address,
– Gateway Address. These addresses are in the format 192.168.000.100. Use the buttons to edit the values as required.
RESET
- changes the digit being edited to the right. Will stop at the right most digit
RESET +
- changes the digit being edited to the left. Will stop at the left most digit
UP
- increases the digit by 1
DOWN
- decreases the digit by 1
RECALL
- aborts the edit process
SET
- enters the sub menu item for editing and when pressed again saves data and exits
5.9
Sets the sense for the Pulse Output. Press the
SET
button to change the sense of the Pulse Output and use the
UP
button
to select NEGative or POSitive. Press
RECALL
to exit up one level without making a change or press
SET
to save the
change.
5.10
Sets the Display Update Rate. Press the
SET
button to change the display update rate and use the
UP
button to select
½
,
1
or
1.5
second update rate. Press
RECALL
to exit up one level without making a change or press
SET
to save the change.
