MONARCH INSTRUMENT ACT-3X, Руководство пользователя и справочное руководство

Страница: 14 / 24

Page 10
5.1.4.1

12 SEC - Sets the Low End to 12 Seconds, equivalent to 5 RPM.
5.1.4.2

1 SEC - Sets the Low End to 1 Second, equivalent to 60 RPM.
5.1.4.3

HALF - Sets the Low End to 1/2 Second, equivalent to 120 RPM.
5.1.5 
GATE - Press the SET button to enter the settings for the GATE time (internal measurement rate)
and use the UP

button to scroll through the options described below. Press the
SET
button to
select the new setting or the RECALL button to exit without saving the settings.
5.1.5.1

STD - Sets the gate to the Standard rate – 32.768 msec.
5.1.5.2

FAST - Sets the gate to the FAST rate – 4.096 msec.
5.2

Sets the Auxiliary input function. This menu item has a number of sub items. Once selected with the
SET
button, the
instrument will display its current function. To exit back to the main menu without changing the function, press the
RECALL
button. If you wish to change the function, you can view the options using the UP

button. The available
options are shown below and are described in Section 4.2 . When the desired function is displayed, press the SET button.
The unit will return to the last menu level.
5.2.1 
TYPE - Press the SET button to enter the sub menu selections shown below and use the UP

button to scroll through the options.
5.2.1.1

OFF - Turns OFF the Aux input so that it has no function.
5.2.1.2

SECAP - Sets the Aux input to be the second input for the SECAP mode. See Section 4.2.3 .
5.2.1.3

INHIBIT - Sets the Aux input to disable the input. See Section 4.2.2 .
5.2.1.4

RESET INPUT - Sets the Aux input to RESET the current Display Total Value. See Section
4.2.4 .
5.2.1.5

RESET ALARM - Sets the Aux input to be the ALARM reset. See Section 4.2.5 .
5.2.2 
INPUT - Press the
SET
button to change the sense of the Aux input and use the UP

button to
select NEGative or POSitive. Press the SET button to select the new setting or the RECALL
button to exit without saving the settings.
5.3


Sets the decimal point on the displayed reading. To enter this menu item press the SET button. The unit will display the
current decimal point setting. To select a different decimal place, press the UP

button, which will toggle between 1, 2, 3
and NONE. Press the SET button to change the decimal point setting to the option displayed and exit back to the menu. To
exit back to the main menu without changing the mode, press the RECALL button.
5.4

Used to set or show the ALARM 1 SETUP parameters. This menu item has a number of sub items. Once selected with the
SET button, the instrument will display its current setting. If you wish to change the alarm setup, you can view the options
using the UP

button. The available options are shown below and are described in Section 4.4 . When the desired
function is displayed, press the SET button. The unit will return to the last menu level. To exit back to the main menu
without changing the values, press the
RECALL
button.
5.4.1 
Set Type - Select the ALARM TYPE. Press the
SET
button to enter the sub menu selections
shown below and use the UP

button to scroll through the options. Press the SET button to
select the new setting or the
RECALL
button to exit without saving the settings.
5.4.1.1

OFF - Turns the Alarm OFF so that it has no function.
5.4.1.2


HIGH - Sets the Alarm to HIgh type.
5.4.1.3


LOW - Sets the Alarm to LOw type.
5.4.2 
LATCH - Press the
SET
button and use the UP

button to select whether the Alarm is
LATCHing – select YES , or NON-LATCHING – select NO . Press the SET button to select the
new setting or the
RECALL
button to exit without saving the settings.
5.4.3 
LOCK - Press the
SET
button and use the UP

button to select whether the Alarm will LOCk
out – select YES , or NO . Press the SET button to select the new setting or the RECALL button to
exit without saving the settings.