background image

Tool Kit for P-Lock Flag Female Terminal 

Doc No: ATS-6382566HM  Release Date: 01-27-13 

UNCONTROLLED COPY

 

Page 5 of 8 

Revision: A 

Revision Date: 01-27-13 

 

CAUTIONS 

 
1.

 

Manually powered hand tools are intended for low volume or field repair.  This tool is 

NOT

 intended for 

production use.  Repetitive use of this tool should be avoided. 

2.

 

Insulated rubber handles are not protection against electrical shock. 

3.

 

Wear eye protection at all times. 

4.

 

Use only the Molex terminals specified for crimping with this tool. 

 

CAUTION:

 Repetitive use of this tool should be avoided. 

 

Certification 

 
Molex does not certify or re-certify commercial grade hand tools but rather supplies the following guidelines for 
customers to re-certify hand tools. 
 

%

 

This tool is qualified to pull force only.  To re-certify, crimp a terminal to a wire, which has been stripped 
12.7mm (1/2”) long, so there is no crimping of the insulation.  Pull the terminal and wire at a rate no faster than 
25mm (1.00”) per minute.  See the Molex web site for the Quality Crimp Handbook for more information on pull 
testing. 

%

 

When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and 
replaced. 

%

 

This tool is very difficult to disassemble and reassemble.  Customer repair is not recommended. 

Содержание 63825-6670









Отзывы: