Molecular Devices FLIPR Tetra Скачать руководство пользователя страница 230

Страница: 230 / 302

Robotic Integration

230

0112-0109 H

Monitor and Keyboard Placement

The host computer provided with FLIPR

Tetra System is mounted to

the instrument’s right side. This computer provides the only direct user

interface and path to control the instrument. Monitor and keyboard for

this computer are mounted to an adjustable arm on the instrument’s

front right. The following image illustrates this installation.

The host computer, keyboard, and monitor may be moved to a different

location at the user’s discretion. Wherever the host computer is placed,

it must be directly connected to the instrument. It is not possible to

communicate between the host computer running the ScreenWorks

Software and the instrument across a network. A short communication

cable is provided between the computer and instrument. In order to

move the computer, the user may need to provide an alternate cable.

This cable must be a shielded crossover Category 5 cable.

Required access areas

The all inclusive system dimensions (with TETRAcycler and Cell

Suspension) are approximately 53 inches (1346 mm) wide by 29 inches

(737 mm) deep by 70 inches (1787 mm) tall. The FLIPR

Tetra System

is designed with rolling castors so it can be readily moved to make

necessary adjustments and perform maintenance. Leveling feet are

also installed on the lower instrument chassis. These feet are typically

used for stabilizing the instrument when integrated with a robot, but

can also be used to establish a uniform instrument deck level in

situations where the lab floor is not flat. When running an experiment,

please make sure the instrument’s feet are lowered and leveled.
The computer and monitor are mounted to the right front side of the

instrument with the included clamp, requiring a minimum lab space of

85 inches (2159 mm) wide by 61 inches (1549 mm) deep for

maneuverability. A minimum 28 inch (711 mm) square footprint for tip

Содержание FLIPR Tetra















































































































































































































































































































Результаты поиска

Содержание FLIPR Tetra

Отзывы:

Похожие инструкции для FLIPR Tetra

Бренды по названию

Популярные бренды

Molecular Devices FLIPR Tetra, Руководство пользователя

Результаты поиска

Содержание FLIPR Tetra

Отзывы:

Похожие инструкции для FLIPR Tetra

Бренды по названию

Популярные бренды