7
SPECIFICATIONS
Rated voltage
12V d.c.
Square anvil size
3/8 inch
No-load speed
0-280 rpm
Recommended
working temperature
14 ~ 104°F (-10 ~ 40°C)
Recommended
storage temperature
32 ~ 104°F (0 ~ 40°C)
OPERATING INSTRUCTIONS
To reduce the risk of fire, personal
injury, and product damage due to
a short circuit, never immerse your tool, battery pack
or charger in fluid or allow a fluid to flow inside them.
Corrosive or conductive fluids, such as seawater,
certain industrial chemicals, and bleach or bleach-
containing products, etc., can cause a short circuit.
If any parts are damaged or
missing, do not operate this
product until the parts are replaced.
Use of this
product with damaged or missing parts could result
in serious personal injury.
Do not attempt to modify this
RATCHET WRENCH or create
accessories not recommended for use with this
RATCHET WRENCH.
Any such alteration or
modification is misuse and could result in a
hazardous condition leading to possible serious
injury.
To prevent accidental starting that
could cause serious personal injury,
always remove the battery pack from the RATCHET
WRENCH when assembling parts, making
adjustments, cleaning, or performing maintenance.
This cordless RATCHET WRENCH must be used only
with the battery packs and chargers listed below:
Battery Pack Selection:
B121001SZ, B121303SZ, B121505SZ, B122010SZ.
Charger Selection:
C05MS1US, C10S1US, C20S1US.
NOTICE:
Please refer to the battery and charger
manuals for detailed operating information.
LED FUNCTIONS OF CHARGER
LED WILL BE ON TO INDICATE STATUS OF CHARGER
AND BATTERY PACK:
•
LED lights up red = Fast charging mode.
•
LED lights up green = Fully charged and in
maintenance charge mode.
•
LED lights up green = When an under-charged
battery pack is inserted into charger, indicates
hot battery pack or that battery pack is out of
normal temperature range or deeply discharged
or defective battery pack.
•
No LED on = Defective charger.
CHARGING THE BATTERY PACK
Battery packs for this tool are shipped in a low
charge condition to prevent possible problems.
Therefore, you should charge it until the green LED
on the front of the charger comes on.
CHARGING A COOL BATTERY PACK
If battery pack is within normal temperature range,
the red LED on charger will come on.
NOTICE:
If the charger does not charge the battery
pack under normal circumstances, return both the
battery pack and charger to your nearest Mokeneye
Authorized Service Center for electrical check.
•
Charge the battery pack only with the charger
provided.
•
Make sure the power supply is normal household
voltage,
110~240 volts, 50/60 Hz, AC only.
•
Connect the charger to the power supply.
•
For C10M1US charger, insert the plug of the
charger into the charging hole of the battery
pack.
•
For C20M1US/C20MK1US charger, place the
battery pack in the charger aligning raised rib on
the battery pack with the groove in the charger.
•
Press down on the battery pack to be sure
contacts on the battery pack engage properly
with contacts in the charger.
•
Normally the red LED on charger will come on.
This indicates the charger is in fast charging
mode.
•
Red LED should remain on for approximately 1 to
2 hours then the green LED will come on. Green
LED on indicates battery pack is fully charged
and charger is in maintenance charge mode.
NOTICE:
The green LED will remain on until the
charger is disconnected from the power supply.
•
After normal usage, a minimum of 1 hour of
charging time is required to fully recharge
battery pack.
•
The battery pack and the charger will become
slightly warm to the touch while charging. This is
normal and does not indicate a problem.
•
Do not place the charger and battery pack in an
area of extreme heat or cold. They will work best
at normal room temperature.
NOTICE:
The charger and battery pack should be
placed in a location where the temperature is
more than 32
°
F but less than 100
°
F.
•
When batteries become fully charged, unplug
the charger from power supply and remove the
battery pack.
CHARGING A HOT BATTERY PACK
When using the tool continuously, the batteries in
the battery pack will become hot. You should let a
hot battery pack cool down for approximately 30
minutes before attempting to recharge. When the
battery pack becomes discharged and is hot, this will
cause the green LED to come on instead of the red
LED. After 30 minutes, reinsert the battery pack in
