Moeller 15-V-SWD Скачать руководство пользователя страница 59

Страница: 59 / 130

Exchange of Modules

After replacement of the modules and connection of the
voltage the configuration button must be pressed. The new
module is assigned an address by this means.

Motor starter or contactor

Device status

The individual SmartWire-Darwin slaves indicate their device
status with the aid of a diagnosis LED.

Table 5:

Diagnostic messages of the SmartWire-Darwin module
for DILM (LED indicator)

Danger!

The exchange of the SmartWire-Darwin module for DILM
must only be carried out with the supply switched off.

Caution!

The order of the SmartWire-Darwin units must not be
altered.

Danger!

The exchange of the motor starter or contactor must only
be carried out after the complete system SmartWire-
Darwin is switched off.

Designation

Colour

State

Message

Ready

Orange

continuous light

Switching command for contactor via
SmartWire-Darwin

Green

continuous light

Device is operating fault-free.

flashing (1 Hz)

• addressing process in progress

– after gateway power On
– after actuation of the

configuration button on the
gateway

• slave not in current configuration
• invalid type

Содержание 15-V-SWD



































































































































Результаты поиска

Содержание 15-V-SWD

Отзывы:

Бренды по названию

Популярные бренды

Moeller 15-V-SWD, Аппаратное обеспечение и инженерия

Результаты поиска

Содержание 15-V-SWD

Отзывы:

Бренды по названию

Популярные бренды