background image

Page 44

Page 1

Fold along dotted line

Fold along dotted line

Global Hobby Distributors

Attn: Global Services

18480 Bandilier Circle

Fountain Valley CA  92728-8610

Post Office 

will not deliver 

without proper 

postage

                                
                                
                                

(Return Address Here)

Kit Product Number  MT3200-1

Check out our website for more information on other exciting Model Tech products!

hTTP://ModelTeCh.GlobAlhobby.CoM

Made in China

FeATureS

ASSEMBLY INSTRUCTIONS

Wing Span:  

67.25 Inches (1708mm)

  

l

 

 Wing Area:

  756 Square Inches (48.77dm

2

)  

l

 

 

length:

  49.5 Inches (1257mm)

Weight rTF:

  5.5-6.5 Pounds (2495-2948gr)  

l

 

Wing loading:

  16.76-19.81 Ounces/Square Foot (51.15-60.45gr/dm

2

)

Functions:

  Ailerons, Elevator, Rudder and Throttle  

l

  

engine required (Glow Version):

  .40 - .52 Two-Stroke or .52 - .61 Four-Stroke

Power System required (electric Version):  

4120/05 Brushless Outrunner / 80 Amp Brushless ESC / 4 Cell 4000mAH LiPO

Completely Prebuilt and Covered with Iron-On Covering Material

Accepts Glow Power and Brushless Electric Power Systems

Stable, Predictable Flight Characteristics

Fiberglass Cowl, Durable Main Landing Gear and Wire-Spoke Wheels

Details Include Wing Struts, Flying Wires, and Moulded Pilot and Cannon

Complete Hardware Set - Wheels, Pushrods, Fuel Tank, Clevises, Etc.

l

 

Fast and Easy Assembly - Over 140 High-Resolution Photos to Guide You

SPeCiFiCATioNS

Model Tech Co., Ltd.

Hong Kong

© 2008, Model Tech Co., Ltd.

All Rights Reserved

Version 1 February 2008

Содержание Blue Max V2 ARF























Отзывы: