The HiRes Video Company
EN
DualMount: Quick Install
MOBOTIX AG • D-67722 Langmeil • Tel: +49 6302 9816-0 • Fax: +49 6302 9816-190 • www.mobotix.com
Installation
1. Prepare opening
Prepare an opening at the desired mounting position of the SurroundMount
that is large enough (diameter about 30 to 40 mm) to allow the sensor cables
to pass through so that you can connect them.
3. Attach the hinged ferrites
Attach one hinged ferrite to each sensor cable (maximum distance to the
connector 10 cm).
2. Lead the sensor cables through the opening
Lead the sensor cables through the opening in the ceiling and allow them to
protrude through (the longer they extend, the easier the installation).
Before installing the sensor modules, make sure that the sensor cables will reach the intended mounting position without placing a strain
on the cables. Separate the sensor modules from the sensor cables before installing the modules.
Further information on the individual camera connectors can be found in Section 2.2.1, “Overview Of Cable Connections” of the S14/S15
camera manuals. Install the base module as described in Section 2.3.1
4. Select mounting type
Select the appropriate mounting type. Depending on the material and the
thickness of the mounting surface, you can mount the DualMount
•
directly
to the ceiling using the five
stainless steel wood screws
(item
1.6) with or without the
dowels
(item 1.7).
• to the ceiling (max. thickness 12 mm) using the
backing plate
(item 1.2)
and the five
stainless steel Allen screws
(item 1.8). To do this, you have
to push the screws through the ceiling and tighten them to the backing
plate positioned to the back of the ceiling.
6. Mount the housing
Place the
seal
(item 1.3) on the
SurroundMount housing
(item 1.1). Attach the
housing with or without
dowels
(item 1.7) to the ceiling using the
stainless
steel wood screws
(item 1.6). When using the
backing plate
(behind ceiling
boards or roof linings) use the
stainless steel Allen screws
(item 1.8). You will
need a
crosstip screwdriver
for the wood screws; for the Allen screws you
will need the
3 mm Allen wrench
provided in the package.
7. Connect sensor cables
Connect a sensor cable to each sensor module (one cable through each
opening of the housing). Insert the sensor cable in the socket of the module,
attach the bayonet catch and turn it to the right until it clicks into place.
8. Attach sensor modules
Make sure that the MOBOTIX lettering on the front of the sensor module is
pointing to the “9-o’clock position” as shown in the figure. Turn the sensor
module with the black module wrench (provided with the S15D) to the right
until it reaches the stop.
9. Secure sensor modules
Tighten the two set screws on the underside of the housing to secure each
of the sensor modules. To do this, use the provided 1.5 mm Allen wrench.
Warning: Do not overtighten the screws (plastic housing!).
5. Set dowels or prepare screw holes
Depending on the desired mounting type, you either set the dowels or prepare
screw holes (for the backing plate). In the second case, you can either use
the drilling template provided at the end of this document or use the backing
plate with its five threaded bushings as a drilling template.
• For surveillance of one area with two sensor modules (in particular, for day and night)
• All available sensor modules (S14D or S15D) can be installed in the DualMount
• Concealed cabling, weatherproof from -30 to +60 °C (IP65)
• Suitable for ceiling installation, with a 25° tilt of the lenses
MX-OPT
-FM-PW
Max. 10 cm!
Ceiling
Seal
Seal
Ceiling
Backing plate
M
O
BO
TIX
M
O
BO
TIX
31.744_EN_V2_06/2013
Day/Night Mount For
Two S14D/S15D Sensor Modules
Delivered Parts
Item
Number
Part Name
1.1
1
Housing
1.2
1
Backing plate
1.3
1
Seal
1.4
1
Allen wrench 1.5 mm
1.5
1
Allen wrench 3 mm
1.6
5
Stainless steel wood screws 4x40
1.7
5
Dowels 6 mm
1.8
5
Stainless steel Allen screws M4x30
1.9
1
Removal tool
1.1
1.2
1.3
1.5
1.7
1.6
1.8
1.9
1.4
