Mx-i26A
32.854-001_EN_06/2017
Quick Install
i26 Hemispheric
Accessories
i26 Hemispheric
• Mx6 system platform with H.264 and ONVIF compatibility
• Includes MxAnalytics video analysis tools out-of-the-box
• Recording on internal MicroSD card (SDXC, SDHC installed)
• Audio package variant (with microphone and speaker) available
• Sensor for temperature integrated
Compact Hemispheric Camera
for Indoor Applications
MOBOTIX 6MP camera for unobtrusive indoor applications,
available as Day or Night version with MX-B016
(Hemispheric) or MX-B036 (103°) lens.
More information:
www.mobotix.com > Products > Indoor Cameras > Hemispheric i26
MxIOBoard-IC
for signal inputs/outputs
MX-OPT-UP1
In-Wall Installation Set
MX-OPT-AP2
On-Wall Installation Set
i26 Standard Delivery
1.2
1.1
1.13
1.14
1.3
1.5
1.6
1.9
1.8
1.12
1.11
1.10
1.7
1.4
Item
Count Part Name
1.1
1
Housing (installed)
1.2
1
Back cover (installed)
1.3
1
Main board with lens MX-B016 or MX-B036
(installed)
1.4
2
Bayonet catch, blue (installed)
1.5
1
USB plug, blue (installed)
1.6
1
Ethernet plug, blue (installed)
1.7
1
Ethernet patch cable, 50 cm/19.7 in, black
1.8
1
Wall sealing
1.9
2
Screw plug, white
1.10
2
Washer Ø 4.3 mm, stainless steel
1.11
2
Wood screw 4x40 mm, stainless steel
1.12
2
Screw anchor S6
1.13
1
MicroSD card pre-installed (SDHC installed, SDXC
supported)
1.14
1
Allen wrench 2.5 mm
Connection and Initial Operation of the i26
Power/Status
Recording
Key
You can find detailed information on the
installation
and
connections of the i26 in the Q25 Camera Manual
(PDF, available on
www.mobotix.com
> Support >
Manuals).
Please note that the boot options of this camera have changed compared
to its predecessor (see
«Boot Options of the i26» on page 2) and the
camera only has one key. Regarding the rest of the
initial operation of the
i26, please see the
Q25 Camera Manual in Chapter 3, «Initial Operation».
Use a suitable device for operating the camera key (e.g., an opened paper
clip).
Standard Delivery i26 In-Wall Installation Set (Accessory)
2.2
2.1
2.4
2.3
Item
Count Part Name
2.1
1
Mounting plate, stainless steel
2.2
1
Cavity wall socket
2.3
2
Allen screw M4x8 mm, stainless steel
2.4
2
Washer Ø 4.3 mm, stainless steel
Standard Delivery i26 On-Wall Installation Set (Accessory)
3.1
3.2
Item
Count Part Name
3.1
1
On-Wall Installation Set
3.2
2
Wood screw 4x70 mm, stainless steel
Installing the MxIOBoard-IC
For the i26, you can use the optionally available MxIOBoard-IC to attach external sensors using the signal inputs
and to switch other devices via the signal outputs.
1. Insert the MxIOBoard-IC
On the back of the camera, remove the sticker
that protects the receptacle and the camera’s
interior from collecting dirt (see red arrow in
figure to the right).
Carefully push the module board onto the
receptacle.
When attaching the connection wires to the
MxIOBoard-IC, make sure the wires are guided
to the module without tension (you could apply
a cable tie and tie the wires to the network
cable, for example).
2. Attach the connection cables
Attach the connection wires as shown in the terminal connector overview.
Terminal Connectors
MxBus functionality is only available with a later hardware
release of the camera.
Output 1 A
Relay
pot.-
free
–
Out-
puts
Output 1 B/GND
Output 1
12 V
Output 1 12 V
–
Output 2 A
Relay
pot.-
free
–
Output 2 B/GND
Output 2
12 V
Output 2 12 V
–
Input 1 –
Inputs
Input 1 +
Input 2 –
Input 2 +
Installation Without In-Wall Installation Set
Use the drilling template on the back for this step. Mark the holes for dowels or screws (blue) and the cut-out for the cables
(red). If required, drill the holes for the dowels, push them in and cut the cut-out for the cables. Guide the Ethernet cable
and any other cables that are to be connected through the cut-out.
1. Press wall sealing on i26
Press the wall sealing on the back of the i26 and
make sure that it lies flat all around the rim.
Note that the labels of the sealing are pointing
toward the back of the camera.
2. Connect the cables
Insert the cables into the appropriate connec-
tors and fasten them using the blue bayonet
catches.
3. Install the i26
Press the camera and the wall sealing against
the wall and align the holes with the holes for
the dowels or screws. Insert the screws with
washers and tighten them cautiously.
4. Apply screw plugs
Push in the screw plugs to close off the holes
with the screws. When doing so, make sure
that the notches in the plugs follow the guides.
Ethernet
USB
Inserting/Exchanging the SD Card
All camera models can use the integrated microSD card (SDXC) to record video data. In order to exchange the microSD card, please proceed as outlined
in the following instruction. For information on reliable SD cards, please see the MOBOTIX website
www.mobotix.com
> Support > MxMedia Library >
Planning in the document MicroSD Card Whitelist for MOBOTIX Cameras. If the camera has already been installed, follow the instructions in section
Caution:
In order to avoid damage from electrostatic discharge, you should touch a grounded device before opening the housing of the camera (e.g.,
the blank metal at the back of a computer). This will remove any static electricity that may have built up.
1. Remove the cables on the back
Release the blue bayonet catch, then remove
the patch cable.
If a USB cable is attached, remove this cable
in the same way.
Lay aside the wall sealing of the camera.
2. Remove the back cover
Insert a suitable device into the hole at the
top of the back cover as shown until you feel
resistance.
In order to release the back cover,
cautiously
press upward as indicated by the blue arrow.
If you are using a flat-head screwdriver, simply
turn the screwdriver.
Gently pull the back cover a bit backward
1
,
then lift the back cover upward to remove it
2
.
3. Remove the main board
Release the main board by
gently pressing
the snap-fit hook beneath the main board as
indicated by the red arrow.
Push the main board out of the housing by
gently applying pressure onto the lens holder
(push upward, since the main board is tilted
downward 15 degrees).
Take care that the lens holder does not catch
in the tunnel or the snap-fit hook.
4. Remove/insert SD card
If a microSD card has been installed, gently press
with your finger as indicated by the arrow until
you hear a
click. Then release the SD card. The
card is protruding slightly and can be easily
removed.
Insert the new microSD card and gently press
with your finger as indicated by the arrow until
you hear the
click.
5. Insert the main board
Insert the lens into the tunnel of the housing
as shown.
Caution:
If the audio package has been installed,
make sure that you do not damage the speaker
cable.
Put your thumbs onto the two lower screws
of the main board (red circles) and cautiously
press on the screws until the main board clicks
into place.
6. Insert the back cover
Insert the back cover at the bottom
1
, then
push shut at the top
2
and press until it clicks
into place.
7. Re-connect the cables
Press the wall sealing onto the back of the i26
and make sure that it lies flat all around the rim.
Note that the labels of the sealing are pointing
toward the back of the camera.
Insert the Ethernet cable and – if installed – the
USB cable into the corresponding sockets and
secure the connectors using the blue bayonet
catches.
1
2
Click!
2
1
