D26 Dome
Quick Installation
20.032.815-04_EN_02/2020
Standard Delivery D26
1.1
1.16
1.15
1.3
1.13
1.12
1.14
1.2
1.4
1.5
1.7
1.8
1.9
1.10
1.19
1.18
1.17
1.11
1.6
Item
Count
Part Name
1.1
1
Camera housing
1.2
1
Lens (not with D26 Body)
1.3
1
Dome, transparent
1.4
1
MicroSD card (SDXC, SDHC pre-installed)
1.5
1
Ethernet cable CAT5 0,5 m/20" (pre-installed)
1.6
1
Hinged ferrite
1.7
1
Allen wrench 3 mm
1.8
1
Torx wrench TX20
1.9
1
Toothed wrench
1.10
1
Outer shell
1.11
1
Mounting ring
1.12
4
Stainless steel washers 5,3 mm dia.
1.13
4
Dowels 8 mm
1.14
4
Stainless steel Torx screws 4,5x60 mm
1.15
4
Stainless steel washers 4,3 mm dia.
1.16
4
Stainless steel Allen screws M4x16 mm
1.17
1
Single-wire plug, black (MxBus)
1.18
2
Single-wire connector
1.19
1
MxBus plug with two-wire connection line
Connections and Initial Operation of the D26
You can find detailed information on the
installation
and
connections
of the D26 in the Camera Manual D26 (PDF, available on
www.mobotix.com > Sup-
port > Download Center > Documentation > Manuals
).
Please note that the boot options of this camera have changed compared to its predecessor (see «Boot Options of the D26» on page 2) and the camera only
has one key ("R"). Regarding the rest of the
initial operation
of the D26, please see the Camera Manual D26 in Chapter 3, «Initial Operation».
Outer shell
Dome
LEDs
Lens
"R" key
Mounting
ring
Network
connection*
USB
MxBus
Slot for MicroSD card
*To suppress electromagnetic interference, attach the enclosed hinged ferrite (item 1.6) to the pre-installed Ethernet cable of the camera. The hinged ferrite
should be positioned as close as possible to the camera body.
Mounting Options of the D26
Preparing the camera for mounting
Remove the outer shell and unscrew the dome.
Installation on Walls or Ceilings Without Accessoires
After drilling the holes for fixtures (see «Drilling Templates»), attach the
mounting ring of the D26 at the designated position using dowels and screws.
Next, connect the cabling, point the camera into the viewing direction and
adjust the focus of the lens (see «Initial Operation of the«Initial Operation
of the D26»). Finally, install the dome and the outer shell.
Installation With On-Wall Set/On-Wall Set 10° (Accessory)
After drilling the holes for fixtures (see «Drilling Templates») attach the
On-Wall Set at the designated position using dowels and screws, then
lead the cabling into the On-Wall Set. Next, remove the mounting ring of
the D26, connect the cabling and install the camera on the On-Wall Set.
Finally, install the dome and the outer shell.
Installation With In-Ceiling Set (Accessory)
After cutting out the hole (see «Drilling Templates»), remove the mounting
ring of the D26 and install the camera in the Cavity Wall Installation Set.
Next, connect the cabling and install the camera together with the Cavity
Wall Installation Set into the cut-out and fasten it using the winged cams.
Finally, press the decoration ring onto the camera and lock it in place using
the toothed wrenches.
Installation With Outdoor Wall Mount (Accessory)
Remove the cover plate of the Outdoor Wall Mount. After drilling the holes
for fixtures (see «Drilling Templates»), attach the Outdoor Wall Mount at
the designated position using dowels and screws, then lead the cabling
into the mount. Next, remove the mounting ring of the D26, connect the
cabling and click the camera into the clamps of the cover plate of the
Outdoor Wall Mount. Then attach the cover plate with the camera to the
Outdoor Wall Mount. Finally, install the dome and the outer shell.
Installation With Pole MOunt and Outdoor Wall Mount (Accessory)
Lead the cabling from the rear through the Pole Mount and attach to a pole
(using steel straps). Then attach the Outdoor Wall Mount to the Pole Mount.
The remaining installation of the D26 follows the steps under «Installation
With Outdoor Wall Mount (Accessory)» above.
Installation of the Vandalism Set (Accessory)
Screw in the reinforced dome and set the four spacers onto the mounting
ring of the camera. Place the stainless steel outer shell onto the camera
and tighten it using the four security screws.
100 mm
Ø 5,5 mm
100
mm
141.4
mm
4x
Inserting/Exchanging the SD Card
All camera models can use the integrated MicroSD card (SDXC) to record video data. In order to exchange the MicroSD card, please proceed as outlined
in the following instruction. For information on reliable SD cards, please see the MOBOTIX website
www.mobotix.com > Support > Download Center >
Documentation > White Lists
in the document MicroSD Card Whitelist for MOBOTIX Cameras.
When replacing the SD card, make sure that recording has been deactivated in the browser (
Admin Menu > Storage > Storage on External File Server /
Flash Device
; activate recording again in the same dialog after exchanging the card).
1. Remove the SD Card
If a MicroSD card has been installed, gently
press with your finger as indicated by the arrow
until you hear a
click
. Then release the SD
card. The card is protruding slightly and can
be easily removed.
2. Insert the SD Card
Insert the MicroSD card and gently press with
your finger as indicated by the arrow until you
hear another
click
.
Make sure that the SD card is fully inserted.
Click!
Click!
Accessories
Mx-D26A/B*
with Outdoor Wall Mount
Mx-D26A/B*
with On-Wall Set/
On-Wall Set 10°
Mx-D26A/B*
with In-Ceiling Set
Mx-D26A/B*
with Vandalism Set
*Variant Mx-D26B supports MOBOTIX MxBus modules
Note on Using the D26 With Lens B237
When using the D26 with the lens B237, you must tilt the lens by at least
5 degrees downward! If this angle is lower than 5 degrees, you will expe-
rience image distortions induced by the curvature of the dome!
>= 5 °
D26 + B237
