manualshive.com logo in svg

ML System Two D Series, Инструкция по установке и обслуживанию, Страница: 50 / 68

Поделиться
Скачать
ML System Two D Series Скачать руководство пользователя страница 50

System Two LED Installation and Service Manual (1003385 Rev. C)

 

Page 50

 

Section 5 

Adjusting the Optional Brake 

 

 

Figure 28: Adjusting the optional brake 

 

Adjust the brakes such that the Light Head or 
Monitor remains stable in any set position and can 
still be conveniently adjusted. 

Follow the safety instructions on Page 56. 

Dismantling the cover panels and moving the cover 
plates 

1.  On each side push the PUSH button 

①

 labeled 

"PUSH" and accept. 

2.  Unscrew 1 cross recessed head screw 

② 

from each 

side. 

  Use a Torx T10 screwdriver. 

3.  Remove 1 cover panel 

③

 from each side. 

  To do this, gently disengage the latches. 

4.  Push the upper and lower cover plate 

④

 

backwards. 

Setting 

  Use a suitable slotted screwdriver. 

To increase the brake force 

  Insert the slotted screwdriver into the brake screw 

⑥

 as illustrated in the Figure and turn it in the 

clockwise direction. 

To reduce the brake force 

  Insert the slotted screwdriver into the brake screw 

⑥

 as illustrated in the Figure and turn it in the 

counter-clockwise direction. 

5.  Perform a function test. 

Mounting the cover panels 

6.  Rotate the cutout in the segment securing device

⑤ 

such that it laterally protrudes over the optional 
brake screw or brake screw aperture 

⑥

. 

7.  Place 1 cover panel 

③

 on each side and screw it on 

using 1 cross recessed head screw

②

. 

  To do this, gently engage the latches. 

8.  Insert one PUSH button 

①

 on each side such that it 

is flush with the cover panels 

③

. 

  The PUSH button 

①

 must not protrude. 

Engaging the cover plates 

9.  Push the upper and lower cover plates 

④

 forwards 

and manually insert 2 latches 

⑦ 

each into the cover 

panels 

③

. 

10.  Using a suitable slotted screwdriver, push the cover 

plates 

④

 further into the cover panels 

③

 until they 

audibly click into place. 

 

The latches 

⑦ 

of the cover plates 

④

 have now 

snapped into place. 

11.  Move the Spring Arm up and down and check that 

the cover plates 

④

 are securely in place. 

 

The cover plates must slide in the lateral guides 
without being trapped. 

 

 

Содержание System Two D Series





































































Отзывы:

Нет отзывов