manualshive.com logo in svg

ML System Two D Series, Инструкция по установке и обслуживанию, Страница: 33 / 68

Поделиться
Скачать
ML System Two D Series Скачать руководство пользователя страница 33

System Two LED Installation and Service Manual (1003385 Rev. C)

 

Page 33

 

Section 4 

Preparing the MD21 Spring Arm 

 

Figure 10: Mounting external cables

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

The Figure shows simplified illustrations which 
explain how to lay external cables 

②

 in the MD21 

Spring Arm [3] (the joint securing device on the 
front joint is not shown). The steps for installing 
the Spring Arm are identical for the MD21 and the 
MD21+. 

Marking the cable clips 

1.  Permanently mark the position 

③

 of the cable clips 

④

 on the parallel guide 

①

; 

 

The parallel guide of the Spring Arm starts at the 
reference edge for the dimensioned distances to 
the cable clips 

④

. 

 

If the 3 cable clips 

④

 are not mounted back to their 

previous positions, the side panels are pushed on 
and no longer flush with each other. 

2.  Disengage the 3 cable clips 

④

 laterally from the 

parallel guide using a suitable screwdriver and 
remove them. 

Mounting Cables 

1.  Adjust the vertical lift of the Spring Arm to the 

lowermost horizontal (0°). 

*** Warning ***

 

Electrical Shock Hazard 

If the external cables 

②

 are not laid next to each other 

and without twisting or if the external cables 

② 

are 

damaged, the Arm System is energized. Contact with 
energized components presents a danger to life from 
electrical shock. 

 

Make sure that you lay the external cables 

② 

next 

to each other and without twisting 

 

Do not damage the cable insulations. 

*** Warning ***

 

Damaged external cables 

②

 

can energize the Arm 

System. 

 

Check all external cables 

②

 for damage. Make 

sure you insert them with great care without 
cables/tubes crossing each other without loops and 
without twisting. 

 

Do not damage the cable insulation 

2.  Route the external cables 

②

 towards the parallel 

guide 

①

 at the bottom of the Spring Arm and then 

route them through the Spring Arm next to each 
other and without twisting as illustrated n the 
Figure. 

 

To do this, make sure that you centrally lay the 
external cable with the largest cross section as 
illustrated in the Figure. 

 

Содержание System Two D Series





































































Отзывы:

Нет отзывов