ML System Two D Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 68

ML System Two D Series Скачать руководство пользователя страница 15

System Two LED Installation and Service Manual (1003385 Rev. C)

Page 15

Section 2

Section 2: Product Specifications

Mechanical Specifications

Parameter

Value

Weights:

Ceiling Mounting Plate

Single Central Axis
Dual Central Axis
Triple Central Axis

Spring Arm

– L21

Spring Arm

– LCH

Spring Arm

– MD21 (Monitor Spring Arm)

Light Head assembly

Power Box (Dual Light)

Approximately   7.2 lbs (3.3kg) to 58.2 lbs (26.5kg)

Approximately  20.9 lbs (9.5kg)
Approximately  38.3 lbs (17.4kg)
Approximately  54.3 lbs (24.7kg)

Approximately  16.1 lbs (7.3kg)
Approximately  14.3 lbs (6.5kg)
Approximately  16.5 lbs (7.5kg)

Approximately  28.1 lbs (12.8kg)

Approximately  8.8 lbs (4.0kg)

Dimensions:

Ceiling Mount Plate

Available Ceiling Rod lengths

Central Axis Extension Arm lengths - Single

Central Axis Extension Arm lengths - Dual

Central Axis Extension Arm lengths - Triple

Spring Arm length

Light head assembly

11.2

” (290mm) Hex Mounting Plate

8

” 16” 24” 32” 39” 47”

(200mm) (400mm) (600mm) (800mm) (1.0m) (1.2m)

41.3” (1,050mm)

41.3” (1,050mm) / 35.4” (900mm)

41.3” (1,050mm) / 35.4” (900mm) / 29.5” (750mm)

36.2

” (920mm)

25.5” (648 mm) Dia. x 4.75” (120 mm) deep

Electrical Specifications

Voltage
Input Voltage

100 - 240 VAC 50/60 Hz

– Single Phase

LED life

50,000 hours (average)

Power:

Single
Dual
Triple

180 Watts
360 Watts
540 Watts

«
...
13
14
15
16
17
...
»

Содержание System Two D Series





































































Отзывы:

Нет отзывов