manualshive.com logo in svg

MKS Newport IDL280-1200LM, Руководство пользователя

Поделиться
Скачать
MKS Newport IDL280-1200LM Скачать руководство пользователя страница 21

11

IDL280-LM Series

Long Travel Industrial Linear Stages

5.0  —

Stage Installation

5.1

Unpacking

The IDL280-LM stage will be delivered in packaging that is designed for

safe transport. Attached to the body of the stage are lifting rings for safe

removal from packaging. It is recommended to carefully lift and move the

stage from packaging using these rings.

CAUTION

Using a beam, lift the lifting rods vertically, as slings with single point
attachment (triangular shape) will induce side and bending loads to the
IDL280-LM stage, especially for configurations where the weight is
higher than 132 lb (60 kg).

NOTE

Allen keys are supplied for CHc M6 and CHc M8 screws as well a 13-mm
open-end wrench for dismantling the spacer tubes.

The stage will come with a control report that indicates performance of

your stage within guaranteed specifications. These measurements were

taken in a controlled environment and flat mounting conditions.

5.2

Setting Up

The IDL280-LM stage is equipped with lifting rings and 2 brackets to lock

the carriage during transportation. To safely unpack the stage, follow the

instructions below

4 LIFTING RINGS

2  LOCKING BRACKETS

8 RODS

CAUTION

Remove lifting and locking

systems before using.

A1045F0 - EDH0362En1050 — 02/20

Содержание Newport IDL280-1200LM































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды