MKS 356 Micro-Ion Plus Series Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 76

MKS 356 Micro-Ion Plus Series Скачать руководство пользователя страница 56

Chapter 3

56

Micro-Ion

®

Module Instruction Manual - 356007-GP

You may also ground pin 11 on the 15-pin subminiature D connector to
lock the CAL, Gauge, Degas, and Trip Points buttons on the module.

To unlock the buttons, remove the pin 11 ground.

If you’ve locked the buttons by grounding pin 11, you cannot use the KBU
command via RS–485 to unlock them. Remove the ground before sending
the KBU command.

KBU – Unlock the
Keyboard

After you’ve locked the CAL (or ATM), Gauge, Degas, and Trip Points
buttons, use the keyboard unlock (KBU) command to unlock them.

KBU command from host:

#01KBU

↵

Response from module:

*01 PROGM OK

↵

If you’ve locked the buttons by grounding pin 11 on the 15-pin
subminiature D connector, the KBU command will not change the locked
state. Remove the ground before sending the KBU command.

FAC – Reset the Values to
Factory Defaults

Table 3-19 lists default settings for the RS-485 version of the module. After
you’ve reconfigured the module, you must cycle power to the module
before the new settings will take effect.

You may restore parameters listed in Table 3-19 to their default values by
sending a factory reset (FAC) command.

FAC command from host:

#01FAC

↵

Response from module:

*01 PROGM OK

↵

Reset command from host:

#01RST

↵

Response from module:

None

Table 3-19 Factory Default Settings for RS-485 Module

Parameter

Default Setting

Digital communication

• Parity: 8 data bits, no parity, 1 stop bit
• Baud rate: 19.2 kbaud
• Module address: 01
• Address offset: 00

Emission current threshold

• 5 x 10

–6

Torr (7 x 10

–6

mbar, 7 x 10

–4

pascal) with decreasing pressure

• 1 x 10

–5

Torr (1 x 10

–5

mbar, 1 x 10

–3

pascal) with increasing pressure

Relays

• Trip point: Sets to 0.0 vacuum pressure; relay must be configured to be operable
• Hysteresis and activation direction: Relay activates at 10% above vacuum pressure trip

point (–) with decreasing pressure

Pressure output units and
optional pressure display

Pressure unit is Torr, mbar, or pascal as specified on sales order and catalog number tag

«
...
54
55
56
57
58
...
»

Содержание 356 Micro-Ion Plus Series













































































Отзывы:

Нет отзывов