manualshive.com logo in svg

MK Martin Pulsar PTM48, Руководство оператора, Страница: 25 / 32

Поделиться
Скачать
MK Martin Pulsar PTM48 Скачать руководство пользователя страница 25

25

Drive Belt

#36855 B76 V Belt

 - 21/32’’ Width X 79’’ Length

It is important to periodically check belt tension and condition. Frayed, cracked or worn drive belts should be replaced 

immediately. 
The clutch on the engine shaft features an internal brake. When engaged, it brakes the engine pulley to stop the belt dive 

and blade pulleys. When the belt is in worn or loose, the ability to stop the rotor quickly may be affected.

IMPORTANT! When changing or removing drive belt check belt tension, adjust if required. 
Wear appropriate personal protection equipment.

Remove Belt

Make sure the engine is off, key is removed and pocketed 

and components are cool to touch before starting this 

procedure. Be aware of possible sharp edges and 

confined working space.

1.  Remove left and right pulley shields and carefully set 

them aside:

•  Remove the two bolts that hold each shield to the 

deck.

•  Loosen (do not remove) the two nuts that hold 

each shield to the motor mount. 

•  Clean out any debris inside the drive 

compartment.

2.  Release the tension on the belt by removing the idler 

wheel tension turnbuckle nut and washer.

3.  Remove the turnbuckle and tension spring from the 

idler arm for clear access to the belt.

4.  The belt should be loose enough to carefully remove 

from the pulley’s.

Install Belt

Inspect and clean the pulleys, check that the idler arm is 

free and easy to move. Grease the idler arm weldment 

grease zerk if required.
1.  Install the new belt onto the pulleys (see belt routing 

below for reference)

2.  Attach the turnbuckle and spring, and insert the 

turnbuckle into the spring bracket hole, fasten the 

washer and nut.

3.  Tighten the nut to apply tension. Tension is correct 

when the spring measures 9.2 cm to 9.5cm (3.625 to 

3.75“).

Left pulley shield

Right pulley shield

Turnbuckle and 

tension spring

Idler wheel & idler 

arm 

!

CAUTION

Operational Hazard

Personal Protection Equipment 

(PPE) is required when operating 

or maintaining this machine.

SNL00001

Содержание Pulsar PTM48

































Отзывы:

Нет отзывов