background image

4

 

Warranty

Eff ective on products retailed on or after November 1, 2017

Two Year Limited Consumer Warranty

Five Year Limited Consumer Warranty on Gearboxes

90 Day Limited Commercial Warranty including Gearboxes

Commercial includes rental and industrial applications.

Warranty begins at the time of customer delivery and is activated upon warranty registration receipt 

at MK Martin Enterprise Inc. 

Warranty coverage is null and void unless the Warranty Registration form has been completed 

in full and is on fi le    at MK Martin Enterprise Inc.

 

Keep your registration copy in a safe place, it is required as proof of warranty activation.

This new and unused product is warranted by 

MK Martin Enterprise Inc.

 to be free from defects in material and workmanship under 

normal use and regular service as described in the owner’s manual, for a consumer period of 2 years and 5 years for gearboxes, 

from the date of delivery, and commercial period of 90 days, including gearboxes, from the date of delivery. Warranty is limited to 

the replacement of parts and / or repair of the product.

If issues develop within the warranty period with the product, contact the local dealer from which you purchased the unit. Only 

MK 

Martin

 authorized dealers may make repairs to the product or aff ect the replacement of defective parts, unless otherwise approved 

by 

MK Martin

. Repairs / replacement will be done at no charge within a reasonable time after the receipt of the product. 

This warranty does not cover the following items:

1.  Normal replacement of service items.

2.  Normal maintenance or adjustments.

3. 

Machines or parts lost or damaged during shipment,

4.  Accessory items / parts not supplied by 

MK Martin 

5. 

Damages resulting from:

 

misuse, negligence, accident, theft or fi re

 

use of improper or insuffi  cient fuel, fl uids or lubricants

 

use of after market parts or accessories, unless approved by 

MK Martin

 

modifi cations, alteration, tampering or improper repair 

 

any device or accessories installed by other than an authorized dealer. 

6.  Tires are covered by the manufacturer of the tire and the warranty period specifi ed by that manufac-

turer. 

Please contact the tire manufacturer for warranty on these items.

MK Martin Enterprise Inc.

 shall not, in any event, be liable for any losses, damages or costs; to include profi ts, travel, transportation, 

pick up, delivery, towing cost, tow vehicle, loss of use, whether special, incidental, consequential or otherwise, in any way. Unit or 

parts are returned at the customer’s expense.

Include a copy of your completed Warranty Registration form with any claim as proof of warranty activation.
There are no warranties, expressed or implied, other than those specifi ed herein. No agent, employee or other person has any 

authority to vary any of the foregoing provisions.

Warranty coverage is null and void unless the Warranty Registration form has been completed in full and is on fi le at MK Martin Enterprise Inc. 

Warranty begins at the time of customer delivery and is activated upon Warranty Registration receipt at MK Martin Enterprise Inc. 

3950 Steffl  er Rd. 

  Elmira 

 Ontario, Canada  

 N3B 2Z3 

 Email : [email protected] 

 Fax : (519)-664-3695  

 Tel : (519)-664-2752

230817

Содержание Meteor 54









































Отзывы: