Mizuho MOT-5602BW Скачать руководство пользователя страница 18

Страница: 18 / 56

Operation

Charging the battery

Make sure to charge the battery when initially using the purchased product,

or when it has not been used for a long time.

CAUTION

•

Connect the product to the power source provided

with the protective grounding to prevent the risk of

an electrical shock.

•

Make sure to use the dedicated power cord with

the "MIZUHO" logo.

•

Before inserting the power cord into the power

source connector, check that the power source

connector does not have any fluid in it nor is dusty.

•

To shut down the power completely, pull out the

power cord from the medical grade outlet.

Connect the power connector and the medical grade outlet

with the power cord, and turn on the power switch.

Medical grade outlet

Power cord

Power connector

Battery charging starts.

While charging, the battery indicator's yellow section on the operating

table blinks sequentially.

When charging is completed, the battery indicator blinks from yellow

side to green side sequentially.

Yellow Green

NOTE

•

The battery naturally

discharges itself when it is

not being used and is being

stored. Make sure to charge

the battery before use.

•

While the battery is being

charged, you can operate

the operating table by using

ON/OFF

on the control unit.

•

If the battery lamp on the

control unit blinks after usage

of the operating table or

the battery indicator on the

lower part of the operating

table lights up only red while

using, charge the battery

immediately. When the

battery is discharged, only

the AC power is available.

•

The operating table

battery life-span is about

2 years. Once it reaches

its life-span, request your

distributor or Mizuho for a

battery replacement.

•

The life-span for the battery

varies greatly depending

on operating conditions.

The battery could degrade

quicker if charging and

discharging the battery are

repeated frequently after

using the operating table for

short operations.

•

It is recommended that you

charge the battery once a

week on weekends, since

it takes 24 hours to fully

charge the battery.

•

If all the battery indicators

do not light up even after

the battery is charged or the

battery gets discharged soon,

the battery may degrade.

Request repairs from your

distributor or Mizuho.

Содержание MOT-5602BW

























































Результаты поиска

Содержание MOT-5602BW

Отзывы:

Mizuho MOT-5602BW, Руководство оператора, Страница: 18 / 56

Результаты поиска

Содержание MOT-5602BW

Отзывы: