Mitsubishi Q2ACPU, Руководство пользователя

Страница: 448 / 570

App - 51
APPENDICES
(2) System information
Table App. 2.3. Special relay
Number Name Meaning Explanation
Set by
(When Set)
Corres-
ponding
ACPU
M9
Corresponding
CPU
SM202 LED OFF command
OFF ON : LED OFF
• When this relay goes from OFF to ON, the LEDs
corresponding to the individual bits at SD202 go off
U New QnA
SM203 STOP contact STOP status • Goes ON at STOP status S (Status change) M9042 QnA
SM204 PAUSE contact PAUSE status • Goes ON at PAUSE status S (Status change) M9041
QnA
SM205 STEP-RUN contact STEP-RUN status • Goes ON at STEP-RUN status S (Status change) M9054 QnA
SM206 PAUSE enable coil
OFF : PAUSE disabled
ON
: PAUSE enabled
• PAUSE status is entered if this relay is ON when the
PAUSE contact goes ON
U M9040 QnA
SM210 Clock data set request
OFF : Ignored
ON
: Set request
• When this relay goes from OFF to ON and after END
instruction execution of subsequent scan, clock data
stored in SD210 to SD213 are written to the CPU
module.
U M9025 QnA
SM211 Clock data error
OFF : No error
ON
: Error
• ON when error is generated in clock data (SD210 to
SD213) value, and OFF if no error is detected.
S (Request) M9026 QnA
SM212 Clock data display
OFF : Ignored
ON
: Display
• Displays clock data as month, day, hour, minute, and
second at the LED display at front of CPU
module.(Enabled only for Q3ACPU and Q4ACPU) U M9027
Q3A
Q4A
Q4AR
SM213
Clock data read
request OFF : Ignored
ON
: Read request
• When this relay is ON, clock data is read to SD210 to
SD213 as BCD values.
U M9028 QnA
SM250 Max. loaded I/O read
OFF : Ignored
ON
: Read
• When this relay goes from OFF to ON, maximum
loaded I/O number is read to SD250.
U New QnA
SM251 I/O change flag
OFF : No replacement
ON
: Replacement
• By turning this relay ON after setting the head I/O
number of the replaced I/O module to SD251, the I/O
module can be replaced online (with power on).
(Only one module can be replaced for each setting.)
• Turn this relay ON in the test mode of the program or
peripheral device for an I/O module change during
RUN, or in the test mode of the peripheral device for
an I/O change during STOP.
• Do not execute a RUN/STOP mode change until I/O
module change is finished.
U M9094
Q2A(S1)
Q3A
Q4A
Q4AR
SM252 I/O change OK
OFF : Replacement
prohibited
ON : Replacement enabled
• Goes ON when I/O replacement is OK. S (END) New
SM255
MELSECNET/10
module 1 information
OFF : Operative network
ON
: Standby network
• Goes ON for standby network(If no designation has
been made concerning active or standby, active is
assumed.) S (Initial) New
QnA
SM256
OFF : Reads
ON
: Does not read
• For refresh from link to CPU module (B, W, etc.)
indicate whether to read from the link module.
U New
SM257
OFF : Writes
ON
: Does not write
• For refresh from CPU module to link (B, W, etc.),
designate whether to write to the link module.
U New
SM260
MELSECNET/10
module 2 information
OFF : Operative network
ON
: Standby network
• Goes ON for standby network
(If no designation has been made concerning active
or standby, active is assumed.) S (Initial) New
QnA
SM261
OFF : Reads
ON
: Does not read
• For refresh from link to CPU module (B, W, etc.)
indicate whether to read from the link module.
U New
SM262
OFF : Writes
ON
: Does not write
• For refresh from CPU module to link (B, W, etc.),
designate whether to write to the link module.
U New
SM265
MELSECNET/10
module 3 information
OFF : Operative network
ON
: Standby network
• Goes ON for standby network
(If no designation has been made concerning active
or standby, active is assumed.) S (Initial) New
QnA
SM266
OFF : Reads
ON
: Does not read
• For refresh from link to CPU module (B, W, etc.)
indicate whether to read from the link module.
U New
SM267
OFF : Writes
ON
: Does not write
• For refresh from CPU module to link (B, W, etc.),
designate whether to write to the link module.
U New
SM270
MELSECNET/10
module 4 information
OFF : Operative network
ON
: Standby network
• Goes ON for standby network
(If no designation has been made concerning active
or standby, active is assumed.) S (Initial) New
QnA
SM271
OFF : Reads
ON
: Does not read
• For refresh from link to CPU module (B, W, etc.)
indicate whether to read from the link module.
U New
SM272
OFF : Writes
ON
: Does not write
• For refresh from CPU module to link (B, W, etc.),
designate whether to write to the link module.
U New
SM280 CC-Link error
OFF : Normal
ON
: Error
• Goes ON when a CC-Link error is detected in any of
the installed CC-Link module. Remains ON if the
condition is restored to normal thereafter. S (Error) New QnA