Mitsubishi PAJERO IV Скачать руководство пользователя страница 19

Страница: 19 / 72

BEFORE ROAD TEST

PRE-DELIVERY INSPECTION

1-13

24. OPERATION OF SERVICE BRAKES
AND PARKING BRAKES

M6010700800274

1. Service brakes

(1) Check the clearance between the brake pedal

and the floor board when the brake pedal is
depressed.

(2) Verify correct brake pedal free play.

NOTE: For inspection and adjustment of the
service brake, refer to GROUP 2, Periodic
Inspection and Maintenance.

2. Parking brake

Check the parking brake drag and lever travel.

NOTE: For inspection and adjustment of the park-
ing brake, refer to GROUP 2, Periodic Inspection
and Maintenance.

25. CLUTCH OPERATION

M6010700900282

1. Check the clutch operation in all driving ranges.
2. Check the pedal to floorboard clearance when the

clutch is just disengaged.

3. Verify correct clutch pedal free play.

NOTE: For inspection and adjustment of the
clutch pedal, refer to GROUP 2, Periodic Inspec-
tion and Maintenance.

26. OPERATION OF SEAT BELTS,
SHOULDER BELTS AND RETRACTORS

M6010701000022

1. Verify that the seat belt warning lamp operates

properly.

2. Check all seat belts and harnesses to assure that

they connect and hold properly.

3. Lean forward to check that the shoulder

harnesses allow movement.

4. Check the condition of the belts and anchors.
5. Check for proper seat belt retraction.

AC305628

Depress the brake pedal
with approximately 500
N force

AC305629

AC305630AC

AC305631

AC305632

Содержание PAJERO IV









































































Результаты поиска

Содержание PAJERO IV

Отзывы:

Похожие инструкции для PAJERO IV

Бренды по названию

Популярные бренды

Mitsubishi PAJERO IV, Руководство по обслуживанию

Результаты поиска

Содержание PAJERO IV

Отзывы:

Похожие инструкции для PAJERO IV

Бренды по названию

Популярные бренды