Mitsubishi PAJERO IV Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 72

background image

BEFORE ROAD TEST

PRE-DELIVERY INSPECTION

1-11

REMOVE FRONT SPRING RESTRAINTS

CAUTION

It is very important that these restraints must be
removed during predelivery-inspection. Failure
to do so could cause ride and handling com-
plaints.

With the vehicle correctly positioned on the
sub-frame contact points, and the suspension fully
extended, remove the rubber restraints from the front
springs.

15. STEERING LINKAGE AND SPLIT PINS

M6010600300023

1. Steering linkage retaining nuts and split pins

Check visually and by feel that the steering
linkage retaining nuts are correctly tightened and
the split pins are correctly installed.

2. Tie rods and relay rod

Check that the tie rods and relay rod of the
steering linkage are not bent and that the tie rod
end lock nuts are securely tightened.

3. Steering components

(1) Check that each of the steering components is

tightened.

(2) Check the tie rod end, nuts and split pins for

proper installation.

(3) Check the condition of bellows-type dust

seals.

4. Split pins

Check the front axle nuts and rear wheel spindle
nuts for split pins.

16. UNDER BODY

M6010600400020

Check under body and under body coating for dam-
age.

BEFORE ROAD TEST

17. SEAT ADJUSTERS AND SEATBACK
LATCHES

M6010700100082

Check the operation of the various parts of the seats.

1. Mechanical adjusters of the seats
2. Operation of the latch for tilting the seatbacks

forward and backward.

18. INHIBITOR SWITCH

M6010701100029

On models with an automatic transmission, be sure
the engine starts in both "P" and "N" position, and
does not start in other positions.

19. IDLE CONTROL KNOB

M6010700300020

Verify that the diesel engine revolution increases
when the idle control knob is pulled out.

AC305605

Spring
restraints

AC305604

AC305622

«
...
15
16
17
18
19
...
»

Содержание PAJERO IV









































































Отзывы:

Нет отзывов

Похожие инструкции для PAJERO IV

Бренд: Daihatsu Страницы: 485

Бренд: Yakima Страницы: 8

Бренд: Yakima Страницы: 8

Бренд: Jackco Страницы: 11

Бренд: GMC Страницы: 499

Бренд: Kia Страницы: 290

Бренд: Phonocar Страницы: 2

Green Motion DC 66

Бренд: Eaton Страницы: 18

MCL-7000 Series

Бренд: Dakota Digital Страницы: 2

Бренд: Volvo Страницы: 284

Бренд: Whispbar Страницы: 14

Бренд: TATA Motors Страницы: 92

Бренд: Streetwize Страницы: 4

2010 MX-5 Miata

Бренд: Mazda Страницы: 8

RAV-4 2015 Series

Бренд: Toyota Страницы: 50

Бренд: Jeep Страницы: 374

Advanced Million Color

Бренд: LedGlow Страницы: 4

Бренд: Honda Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды