background image

143

APPENDICES

A

Appendix 3  Details of R

emote Buffer 

Memory Areas

  

(4) Cyclic data update watch time setting (address: 0007

H

)

This signal is used to set the time to monitor the data update interval of the cyclic transmission (watch time).
When the cyclic transmission remains stopped longer than the cyclic data update watch time, the D/A converter 
module is regarded as disconnected from data link and the output status is held or cleared by Digital output 
HOLD/CLEAR setting (address: 0011

H

) and Analog output HOLD/CLEAR setting (address: 0104

H

).

For Digital output HOLD/CLEAR setting (address: 0011

H

), refer to the following.

 • Digital output HOLD/CLEAR setting (address: 0011

H

) (

Page 144, Appendix 3 (6))

For Analog output HOLD/CLEAR setting (address: 0104

H

), refer to the following.

 • Analog output HOLD/CLEAR setting (address: 0104

H

) (

Page 145, Appendix 3 (9))

(a) Setting range

Setting range is 0 (Not monitor) or 1 to 20 (0.1 to 2 seconds). Set the value in increments of 1 (100ms).

(b) Enabling the setting

Turn on and off Initial data setting request flag (RY9).

(c) Default value

The default value is set to Not monitor (0).

If a value out of the setting range is set, the error code (0930

H

) is stored in Latest error code (RWr0), Error flag (RXA) turns 

on, and the ERR. LED turns on. Then the I/O operation stops.

(5) Input response time setting (address: 0010

H

)

The input response time of the extension input module is set.

(a) Enabling the setting

Turn on and off Initial data setting request flag (RY9).

(b) Default value

The default value is set to 10ms (5

H

).

If data other than the above is set, an error occurs. The error code (1F40

H

) is stored in Latest error code (RWr0), Error 

flag (RXA) turns on, and the ERR. LED turns on.

If no extension input module is connected, the setting in this area is ignored.

Input response time

Setting value

1.0ms

2

H

1.5ms

3

H

5ms

4

H

10ms

5

H

20ms

6

H

70ms

7

H

Содержание NZ2GF2B-60DA4















































































































































































Отзывы: