background image

142

(3) Warning flag assignment (address: 0006

H

)

Warning flag (RX7) is assigned to the remote output (RY) of the extension output module using the external 
signal assignment function. When a minor error occurs, the assigned remote output (RY) turns on.

(a) Setting range

The remote output (RY) number of the extension output module, counted from the start remote output (RY) 
number (0000

H

) of the main module, is set.

Ex.

The following is an example for assigning Warning flag (RX7) to the remote output (RY) number, 6

H

, of 

the extension output module.

The remote output (RY) number, 6

H

, is 26

H

 when counted from the start remote output (RY) number of 

the main module.
Thus, set 26

H

 for Warning flag assignment (address: 0006

H

).

(b) Enabling the setting

Turn on and off Initial data setting request flag (RY9).

(c) Default value

The default value is set to No assignment (FFFF

H

).

If a value out of the setting range is set, an error occurs. The error code (0174

H

) is stored in Latest error code (RWr0), Error 

flag (RXA) turns on, and the ERR. LED turns on. The operation is performed in the previous setting.

0

H

to

to

to

1F

H

20

H

26

H

2F

H

to

to

0

H

6

H

F

H

Main module

Extension module

Содержание NZ2GF2B-60DA4















































































































































































Отзывы: