Mitsubishi NZ2GF2B-60DA4 Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 174

background image

134

(4) Remote READY (RXB)

This signal is used as an interlock condition when the master station reads/writes data to/from the remote register
or remote buffer memory areas of the D/A converter module.
The signal turns on when the module power supply is turned on.
When Error flag (RXA) turns on, the signal turns off.

(5) Alert output signal (RX1E)

If the digital value in any D/A conversion enabled channels becomes any of the following status, this signal is
turned on.

• Digital value > Alert output upper limit value
• Digital value < Alert output lower limit value

(a) How to turn off the signal

Turn off the signal by either of the following methods.

• Turning on and off Alert output clear request flag (RY1E)
• Turning on and off Initial data setting request flag (RY9)

When an alarm code is stored in Latest warning code (RWr1), this signal is cleared.

(6) External power supply monitor state flag (RX1F)

This signal turns on when the external power supply monitoring function is being activated by External power
supply monitor request flag (RY1F).

For the external power supply monitoring function, refer to the following.

• External power supply monitoring function (

Page 98, Section 8.11 (2))

Alert output signal
(RX1E)

Latest warning code
(RWr1)

Alert output clear
request flag (RY1E)

Controlled by the D/A converter module

Controlled by the program

ON

ON

OFF

OFF

0

0

Alert

External power supply monitor
function

External power supply monitor
request flag (RY1F)

Changed by

the user

OFF

OFF

ON

ON

OFF

OFF

Controlled by the D/A converter module

Changed by

the user

External power supply monitor
status flag (RX1F)

Disabled Enabled

Disabled

«
...
134
135
136
137
138
...
»

Содержание NZ2GF2B-60DA4















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NZ2GF2B-60DA4

Бренд: Samson Страницы: 48

Бренд: Mako Networks Страницы: 15

Бренд: CAME Страницы: 32

Бренд: Samson Страницы: 20

Бренд: MADRIX Страницы: 36

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 20

Бренд: Calpeda Страницы: 4

Бренд: Lamtec Страницы: 136

Бренд: Eaton Страницы: 8

Бренд: Rain Bird Страницы: 24

ESP-LXIVM Series

Бренд: Rain Bird Страницы: 16

Бренд: Rabe Страницы: 61

Бренд: Racal Instruments Страницы: 35

Бренд: Samson Страницы: 8

Бренд: Samson Страницы: 60

Бренд: Samson Страницы: 40

Бренд: Abocom Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды