Mitsubishi MZ360360EX Скачать руководство пользователя

Страница: 20 / 51

- 20 -

F. INSTALLING THE ELECTRONIC

CONTROL UNIT

1) Apply the two pieces of double-sided adhesive tape

⑥

and the urethane sheet B

④

on the electronic

control unit

①

as shown in the drawing.

2) Wipe clean and degrease the installation position
of the electronic control unit

①

at the deck

crossmember stay above the steering shaft using
isopropyl alcohol or degreaser.

3) Connect the 13-pin connector and the 12-pin
connector of the harness

③

to the electronic control

unit

①

. Then peel off the backing strips of the

double-sided adhesive tape

⑥

and attach the

electronic control unit

①

to the deck crossmember

stay above the steering shaft.

4) Route the harness

③

along the instrument panel

harness and fix the harness near the electronic
control unit

①

using the tie-wrap

⑦

5) Connect the antenna jack of the antenna unit

②

to the electronic control unit

①

6) Secure the electronic control unit

①

and also the

cable of the antenna unit

②

on the deck

crossmember stay using the tie-wraps

⑦

7) Bundle the excess length of the antenna unit cable
and fix it to the front harness using the tie-wrap

⑦

- Perform this work in a well-ventilated space.

- Never use organic solvent such as thinner, benzine,

gasoline, etc.

Caution

Be sure not to touch the adhesive surface of the

adhesive tape by a dirty hand or glove or remove

and reapply the adhesive tape. Doing so makes

the tape lose much of its adhesion.

Caution

Check

Route the cable of the antenna unit

②

so that it

does not interfere with the steering shaft.

Caution

Содержание MZ360360EX




















































Результаты поиска

Содержание MZ360360EX

Отзывы:

Похожие инструкции для MZ360360EX

Бренды по названию

Популярные бренды

Mitsubishi MZ360360EX, Руководство по установке

Результаты поиска

Содержание MZ360360EX

Отзывы:

Похожие инструкции для MZ360360EX

Бренды по названию

Популярные бренды