Mitsubishi Melsec-Q QD75D1 Скачать руководство пользователя страница 804 | Manualshive

Страница: 804 / 858

background image

Appendix - 118

MELSEC-Q

APPENDICES

BIPOLAR DRIVE CONSTANT-CURRENT
SYSTEM

This is one system for driving a stepping
motor. In this method, the orientation of the
excitation current flowing to the stator coil is
reversed, and the excitation current direction is
in both the positive and negative direction.
This enables the motor coil to be used
effectively, and a large output torque can be
obtained at low speeds.

A phase

Bipolar drive basic circuit (bridge method)

BUFFER MEMORY

Memory used to temporarily store data. Before
writing external data to the CPU module data
memory, it is first temporarily stored in the
buffer memory to be used for operation by the
program. The buffer memory is used by the
positioning module because the latest data
can be read and written.

Positioning module

External

data

Write : TO
Read : FROM

Bus

CPU module

Data
memory

Buffer
memory

Data is written/read
using the following
instructions:

BUSY

The device is doing some other work. It is in a
positioning operation or in dwell time.

CCW (Counterclockwise)

Rotation in the counterclockwise direction. In
the motor, this is determined looking from the
shaft end side. Also refer to "CW".

CHANGE signal

The CHANGE signal is an external signal used
to switch the speed-position control from the
speed control being executed to position
control.

CIRCULAR INTERPOLATION

Automatic operation in which the machine path
makes a circle when positioning is carried out
by simultaneously operating both the
longitudinal feed and latitudinal feed motors.
The normal unit is 90ø. Round shapes can be
created with this type of interpolation, and
obstacles in the machine path can also be
avoided. Refer to the terms "INTERPOLATION
OPERATION" and "LINEAR
INTERPOLATION"

A

B

C

D

Collision

Obstacle

COMMAND PULSE

Refer to term "FEEDBACK PULSE".

COMPOSITE SPEED

The movement speed for the target control
during interpolation operations.

Y axis
speed

Composite speed

X axis speed

CONTROL UNIT

This is one type of positioning reference data.
The unit to be used is designated as mm, inch,
degree, or pulse.

CP CONTROL (Continuous Path Control)

Continuous path is a control method in which a
path is followed without interrupting such as in
uniform speed control.

«
...
802
803
804
805
806
...
»

Содержание Melsec-Q QD75D1



























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Melsec-Q QD75D1

Бренд: KELCO Страницы: 36

Бренд: Parker Страницы: 44

Бренд: Radware Страницы: 98

Бренд: RabbitCore Страницы: 34

Бренд: R82 Страницы: 11

Бренд: ZKTeco Страницы: 14

Бренд: Ziton Страницы: 28

Бренд: Unico Страницы: 164

Бренд: DANIEL Страницы: 48

Бренд: Full Gauge Controls Страницы: 3

Бренд: FrSky Страницы: 2

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: ACS Страницы: 2

Бренд: Litex Страницы: 1

Бренд: Scanreco Страницы: 48

Бренд: IMG STAGELINE Страницы: 14

Бренд: VAT Страницы: 77

ESP32-C3 Series

Бренд: Espressif Systems Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды