Mitsubishi MELSEC iQ-R series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 86

background image

5 SYSTEM CONFIGURATION

5.1 Precautions for System Configuration

27

5

5

SYSTEM CONFIGURATION

Temperature sensor

For usable temperature sensors, refer to the following.



Page 20 Type of Temperature Sensors, Temperature Measuring Range, Resolution, and Effect from Wiring Resistance

Current sensor for heater disconnection detection

The following table lists current sensors for heater disconnection detection available with the R60TCTRT2TT2BW or
R60TCRT4BW.

For how to select current sensors for heater disconnection detection, refer to the following.



MELSEC iQ-R Temperature Control Module User's Manual (Application)

5.1

Precautions for System Configuration

The R60TCTRT2TT2 and R60TCTRT2TT2BW measure temperatures based on the temperature of the terminal block. Thus,
depending on the system configuration used (especially when two or more of the R60TCTRT2TT2 and R60TCTRT2TT2BW
modules are connected next to each other, or the R60TCTRT2TT2 or R60TCTRT2TT2BW is mounted next to the power
supply module or CPU module), the temperature distribution of the terminal block is not uniform due to the effects of heat
generated from modules, and the measured temperature may greatly differ from the actual temperature.
In this case, the error between the measured value and actual temperature can be corrected by the following methods.

Using the sensor correction function

The measured temperature can be corrected to the actual temperature with this function. For details on the sensor correction
function, refer to the following.



MELSEC iQ-R Temperature Control Module User's Manual (Application)

Model

Manufacturer

CTL-12-S36-10 (0.0 to 100.0A)

U.R.D.Co., LTD.

CTL-12-S56-10 (0.0 to 100.0A)

CTL-6-P-H (0.00 to 20.00A)

CTL-6-S-H (0.00 to 20.00A)

CTL-12L-8 (0.0 to 100.0A)

«
...
27
28
29
30
31
...
»

Содержание MELSEC iQ-R series























































































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC iQ-R series

ControlMaster CM15

Бренд: ABB Страницы: 28

Бренд: GARDTEC Страницы: 48

Бренд: FAAC Страницы: 64

FSDrive-MV1000 Series

Бренд: YASKAWA Страницы: 260

Бренд: YASKAWA Страницы: 114

Бренд: YASKAWA Страницы: 20

Бренд: YASKAWA Страницы: 152

Бренд: YASKAWA Страницы: 66

Бренд: YASKAWA Страницы: 20

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 58

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 2

Бренд: YASKAWA Страницы: 58

Бренд: Panasonic Страницы: 8

Бренд: Quinny Страницы: 21

Бренд: Linak Страницы: 2

IntelliCross TouchFree Kit

Бренд: Novax Страницы: 3

Бренд: Daikin Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды