background image

Guidelines for the safety of the user and protection of

the FX-4AD special function block

This manual has been written to be used by trained and competent personnel. This is defined
by the European directives for machinery, low voltage and EMC.

If in doubt at any stage during the installation of the FX-4AD always consult a professional
electrical engineer who is qualified and trained to the local and national standards. If in doubt
about the operation or use of the FX-4AD please consult the nearest Mitsubishi Electric distributor.

Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential
damage that may arise as a result of the installation or use of this equipment.

All examples and diagrams shown in this manual are intended only as an aid to understanding
the text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual
use of the product based on these illustrative examples.

JY992D52601E

Effective APR. 1998

Specifications are subject

to change without notice.

Manual number  : JY992D52601

Manual revision : E

Data                   : APRIL 1998

HEAD OFFICE :   MITSUBISHI DENKI BLDG MARUNOUCH TOKYO 100    TELEX : J24532 CABLE MELCO TOKYO
HIMEJI WORKS : 840, CHIYODA CHO, HIMEJI, JAPAN

Содержание MELSEC-F FX-4AD













Отзывы: