15 - 23 15 - 23
15 TROUBLESHOOTING
15.3.2 Error code list
The following shows the error codes list.
When the standby master station is operating as the master station, the detectability is
identical to that of the master station.
When the standby master is operating as a local station, the detectability is identical to
that of the local station.
Detectability
Error code
(hexadecimal)
Error details
Cause of error occurrence (details)
Corrective action
Master station Local station
4000 to
4FFF
(Errors detected by the
programmable controller CPU)
———
Take corrective actions, referring to
the troubleshooting section of the
MELSEC-L CPU Module User's
Manual (Hardware Design,
Maintenance and Inspection).
―
―
7000 to
7FFF
(Errors detected by serial
communication module, etc)
———
Take corrective actions, referring to
the troubleshooting section of the
MELSEC-L Serial Communication
Module User's Manual.
―
―
B10C
Message transmission function
unsupported
The message transmission function was
executed for the remote device station
that does not support the function.
Check the station No. of the target
station.
Or, check if the target station
supports the message transmission
function.
B110
Transient data can not be
received.
A line error has occurred.
Check the line.
B111
Transient data receiving order
error
A line error has occurred.
Check the line.
B112
Transient data length error
A line error has occurred.
Check the line.
B113
Transient data ID error
A line error has occurred or an
instantaneous power failure has occurred
at the send station.
Check the line, or check the supply
power and power supply module of
the send station.
B115
Link error
A line error has occurred.
Check the line.
B116
Packet error
A line error has occurred.
Check the line.
B120
Forced termination of the
remote device station initialize
procedure registration function
In the remote device station initialize
procedure registration function, the
specification of the remote device station
initialize procedure registration was turned
off before all procedures were completed.
Do not turn the specification of the
remote device station initialize
procedure registration off until all
procedures are completed.
B124
Error at a station on which the
remote device station initialize
procedure registration function
was executed
The specification of the remote device
station initialize procedure registration
function was turned on at a station other
than the master station.
Turn on the remote device station
initialization procedure registration
instruction on the master station
(station No.0).
The specification of the remote device
station initialize procedure registration
function was turned on without setting the
remote device station initialize procedure
registration.
Turn on the specification of the remote
device station initialize procedure
registration function after setting the
remote device station initialize
procedure registration.
B125
Parameter not set error of the
remote device station initialize
procedure registration function
Bits corresponding to other than the head
station number were turned ON in the
Specification of remote device station to
be initialized (SW0014 to SW0017) to
instruct remote device station initialization
procedure registration.
Turn ON only the bit corresponding to
the head station number in the
Specification of remote device station
to be initialized (SW0014 to
SW0017).
B201
Corresponding station error
during sending
A data link error occurred at the
corresponding station during transient
transmission.
Check the communication status of
other stations, whether or not a
temporary error invalid station is
specified, or if the corresponding
station is stopped.
B205
Transient target station error
A transient request was issued to other
than the intelligent device station.
Check the target station.
B301
Processing request error during
link stop
Loop test request was issued while the
link was stopped.
Perform a loop test while the link is
being established
B302
Specified station number
setting error
The specified station number exceeded
the highest communication station
number during temporary error invalid
request/temporary error invalid cancel
request.
Specify a station number that is no
greater than the highest
communication station number.
(To the next page)
Содержание L26CPU-BT
