manualshive.com logo in svg

Mitsubishi MOTORS Eclipse, Руководство пользователя

Поделиться
Скачать
Mitsubishi MOTORS Eclipse Скачать руководство пользователя страница 679

ON-VEHICLE SERVICE

TSB Revision

MULTIPORT FUEL INJECTION (MFI) <3.0L>

13B-679

BASIC IDLE SPEED ADJUSTMENT

M1131001800208

Required Special Tool:

•

MB991502: Scan Tool (MUT-II)

NOTE: The standard idling speed has been adjusted with the 
speed adjusting screw (SAS), by the manufacturer. There 
should be no need for readjustment.
NOTE: If the adjustment has been changed by mistake, the idle 
speed may become too high or the idle speed may drop too low 
when loads A/C, defogger, etc. are placed on the engine. If this 
occurs, adjust by the following procedure.
NOTE: The adjustment, if made, should be made after first con-
firming that the spark plugs, the injectors, the idle air control 
motor, compression, etc., are all normal.

1. The vehicle should be prepared as follows before the 

inspection and adjustment.

•

Engine coolant temperature: 80 

−

 95

°

C (176 

−

 203

°

F)

•

Lights, electric cooling fan and accessories: OFF

•

Transaxle: Neutral ("P" range on vehicle with A/T)

CAUTION

To prevent damage to scan tool MB991502, always turn the 
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991502.

2. Connect scan tool MB991502 to the data link connector (16-

pin).

3. Start the engine and run at idle.
4. Select the item number 30 of the scan tool Actuator test.

NOTE: Use the scan tool to hold the IAC motor at the basic 
step to adjust the basic idle speed.

5. Check the idle speed.

NOTE: The engine speed may be 20 to 100 r/min lower than 
indicated above for a new vehicle [driven approximately 500 
km (300 mile) or less], but no adjustment is necessary.
NOTE: If the engine stalls or the engine speed is low even 
though the vehicle has been driven approximately 500 km 
(300 mile) or more, it is probable that deposits are adhered 
to the throttle valve, so clean it. (Refer to 

P.13B-677

 .)

Standard value: 700 + 50 r/min

6. If not within the standard value range, turn the speed 

adjusting screw (SAS) to make the necessary adjustment.

7. Press the scan tool clear key, and release the IAC motor 

Actuator test mode.

8. Turn the ignition switch to the "LOCK" (OFF) position.

NOTE: Unless the IAC motor is released, the Actuator test 
mode will continue for 27 minutes.

9. Disconnect scan tool MB991502.
10.Start the engine again and let it idle for about 10 minutes. 

Check that the idling condition is normal.

AKX01177

16 PIN

MB991502

AB

AK000115AB

SPEED ADJUSTING SCREW

Содержание Eclipse























































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды