Mitsubishi Electric VS-60HS12U Скачать руководство пользователя страница 14

Страница: 14 / 64

VS-60HS12U Set-up Manual

2.3.1

Screen demounting

Unlocking

Release delivery locking before screen demounting /
mounting.

•

Shipping lock bolts (in screen integrated models)
remove 2 shipping lock bolts (M5-45mm, white hex
socket bolts).

This product has no handles, so take out the cabinet
from the carton tray holding the frame of the cabinet
after demounting the screen.

Demounting

Pull up the screen handles on both sides to draw the
screen unit till locked and put the handles back to
the original positions.

While pressing the release buttons on both sides to
the end, open the lower part of the screen (about
15°) to pull it up on the skew.

Put back the screen-holding arms into the cabinet by
pressing down the slide lock lever on both sides.

Release button

(on both sides)

(1)

15°

(2)

Slide lock lever

(on both sides)

Screen-holding arm

Shipping lock bolts

Screen-drawing

handles

(1)

(2)

Carton tray

Содержание VS-60HS12U

































































Результаты поиска

Содержание VS-60HS12U

Отзывы:

Похожие инструкции для VS-60HS12U

Бренды по названию

Популярные бренды

Mitsubishi Electric VS-60HS12U, Руководство по установке

Результаты поиска

Содержание VS-60HS12U

Отзывы:

Похожие инструкции для VS-60HS12U

Бренды по названию

Популярные бренды