manualshive.com logo in svg

Mitsubishi Electric R16MTCPU, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric R16MTCPU Скачать руководство пользователя страница 23

1  SYSTEM CONFIGURATION

1.1  Motion System Configuration

21

1

*3 When using the sensing module in axis mode, there are no restrictions on the number of stations for the sensing module.
*4 When AlphaStep/5-phase is present, operation is carried out at 0.444ms operation cycle.
*5 When FR-A700 series, VC

 series, or VPH series are present, operation is carried out at 0.444ms operation cycle.

*6 When the setting exceeds the number of control axes per controller, a minor error (error code: 1C83H) occurs.

Set the operation cycle as follows according to the number of control axes per controller.

 • When using MR-J4W-

B, if there is at least one axis which has not been set in servo network setting, all axes of the 

applicable servo amplifier cannot be connected, and all servo amplifiers after the applicable servo amplifier cannot be 
connected. Set "Not used" to the applicable axis with a dip switch for the axis which is not used by MR-J4W-

B.

 • When using a multi-axis servo amplifier (MR-J4W-

B), there is a restriction on the number of connectable units (servo 

amplifier (MR-J4(W)-

B), SSCNET

/H head module, other drivers etc.) between the Motion CPU and the multi-axis servo 

amplifier. The number of connectable units are shown below. When more than the number of connectable units are 
connected, a warning (error code: 0C82H) occurs. While communication with MR-J4W-

B is still possible when the 

warning occurs, communication becomes unstable, therefore the unit configuration should be reviewed. Furthermore, when 
an optical hub unit is used, the number of connectable units is reduced. Refer to the following for details of when an optical 
hub unit is connected.

MELSEC iQ-R Motion Controller Programming Manual (Common)

Number of control axes per controller Operation cycle

1 to 2 axes

0.222ms or more

3 to 4 axes

0.444ms or more

5 axes or more

0.888ms or more

Servo amplifier

Number of connectable units

MR-J4-

B

No restriction

MR-J4W2-

B

1 axis set

2 axes set

14 units or less

MR-J4W3-

B

1 axis set

No restriction

2 axes set

14 units or less

3 axes set

13 units or less

Содержание R16MTCPU



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды