Mitsubishi Electric PQHY-P200-900Y(S)LM-A, Справочник данных

Страница: 104 / 246

101
1. SPECIFICATIONS
HEAT SOURCE
WR2
MEE15K036
Model PQRY-P850YSLM-A
Power source 3-phase 4-wire 380-400-415 V 50/60 Hz
Cooling capacity *1 kW 96.0
(Nominal) kcal/h 82,600
*1 BTU/h 327,600
Power input kW 18.03
Current input A 30.4-28.9-27.8
EER kW/kW 5.32
Temp. range of Indoor W.B. 15.0~24.0°C (59~75°F)
cooling Circulating water °C 10.0~45.0°C (50~113°F)
Heating capacity *2 kW 108.0
(Nominal) kcal/h 92,900
*2 BTU/h 368,500
Power input kW 18.49
Current input A 31.2-29.6-28.5
COP kW/kW 5.84
Temp. range of Indoor D.B. 15.0~27.0°C (59~81°F)
heating Circulating water °C 10.0~45.0°C (50~113°F)
Indoor unit Total capacity 50~150% of heat source unit capacity
connectable Model/Quantity P15~P250/2~50
Sound pressure level (measured in anechoic room) dB <A> 56
Sound power level (measured in anechoic room) dB <A> 71.5
Refrigerant High pressure mm (in.) 28.58 (1-1/8) Brazed
piping diameter Low pressure mm (in.) 41.28 (1-5/8) Brazed
Set Model
Model
PQRY-P450YLM-A PQRY-P400YLM-A
Circulating water Water flow rate m
3
/h 7.20 + 7.20
L/min 120 + 120
cfm 4.2 + 4.2
Pressure drop kPa 44 44
Operating volume range m
3
/h 4.5 + 4.5 ~ 11.6 + 11.6
Compressor Type Inverter scroll hermetic compressor Inverter scroll hermetic compressor
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter Inverter
Motor output kW 11.6 10.7
Case heater kW - -
Lubricant MEL32 MEL32
External finish Galvanized steel sheets Galvanized steel sheets
External dimension H x W x D mm 1,450 x 880 x 550 1,450 x 880 x 550
in. 57-1/8 x 34-11/16 x 21-11/16 57-1/8 x 34-11/16 x 21-11/16
Protection devices High pressure protection
High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
Inverter circuit (COMP.) Over-heat protection, Over-current protection Over-heat protection, Over-current protection
Compressor Over-heat protection Over-heat protection
Refrigerant Type x original charge R410A x 6.0 kg (14 lbs) R410A x 6.0 kg (14 lbs)
Control Indoor LEV and BC controller
Net weight kg (lbs) 216 (477) 216 (477)
Heat exchanger plate type plate type
Water volume in plate I 5.0 5.0
Water pressure Max. MPa 2.0 2.0
HIC circuit (HIC: Heat Inter-Changer) - -
Pipe between unit and High pressure mm (in.) 22.2 (7/8) Brazed 22.2 (7/8) Brazed
distributor Low pressure mm (in.) 28.58 (1-1/8) Brazed 28.58 (1-1/8) Brazed
Drawing External WKS94C750
Wiring WKE94G131 WKE94G131
Standard attachment Document Installation Manual
Accessory Refrigerant conn. pipe
Optional parts Heat Source Twinning kit: CMY-Q200CBK
Joint: CMY-Y102SS/LS-G2, CMY-R160-J1
Main BC controller: CMB-P1016V-HA1
Sub BC controller: CMB-P104, 108V-GB1, CMB-P1016V-HB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Due to continuing improvement, above specifications may be subject to change without notice.
The ambient temperature of the heat source unit needs to be kept below 40°C D.B.
The ambient relative humidity of the heat source unit needs to be kept below 80%.
The heat source unit should not be installed at outdoor.
Be sure to mount a strainer (more than 50 meshes) at the water inlet piping of the unit.
Be sure to provide interlocking for the unit operation and water circuit.
The heat source twinning kit (low pressure) should be connected to the low pressure side of the heat source unit.
Install the supplied insulation material to the unused drain-socket.
When installing insulation material around both water and refrigerant piping, follow the installation manual.
Notes: Unit converter
1.Nominal cooling conditions (subject to JIS B8615-2)
Indoor: 27°CD.B./19°CW.B. (81°FD.B./66°FW.B.), Water temperature: 30°C (86°F)
Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.)
2.Nominal heating conditions (subject to JIS B8615-2)
Indoor: 20°CD.B. (68°FD.B.) ,Water temperature: 20°C (68°FD.B.)
Pipe length: 7.5 m (24-9/16 ft.), Level difference: 0 m (0 ft.) BTU/h =kW x 3,412
cfm =m
3
/min x 35.31
lbs =kg/0.4536
*Above specification data is
subject to rounding variation.
0000003811.BOOK 101 ページ ２０１５年１１月９日 月曜日 午前１１時２０分