Mitsubishi Electric PKFY-P-VKM-E, Руководство по эксплуатации

Страница: 12 / 43

12
GB
2SHUDWLRQ
2
Select the menu with the [F4]
button.
'HIDXOWĺ$UHDĺ'LUHFW,QGLUHFW
ĺ'HIDXOW«
Default: The vanes move the same
as during normal operation.
During cooling mode, all of the
vanes move to the horizontal
airflow direction.
During heating mode, all of the
vanes move to the down airflow
direction.
Area: The vanes move to the
down airflow direction toward
areas with a high floor temperature
during cooling mode and toward
areas with a low floor temperature
during heating mode. Otherwise,
the vanes move to the horizontal
airflow direction.
D i r e c t / I n d i r e c t : T h e v a n e s
automatically move relative to the
areas where persons are detected.
The vanes operate as indicated in
the following table.
3 When Direct/Indirect is selected,
set each air outlet.
Select the air outlet with the [F1] or
[F2] button, and change the setting
with the [F4] button.
After changing the settings for all of
the air outlets, press the [SELECT]
button to save the settings.
* In order to enable this function,
the airflow direction must be set
to “Auto”.
1
Select the desired menu with the
[F1] or [F2] button.
No occupancy energy save
If there are no persons in the room
for 60 minutes or more, energy-
saving operation equal to 2 °C is
performed.
Room occupancy energy save
If the occupancy rate decreases
to approximately 30% of the
maximum occupancy rate, energy-
saving operation equal to 1 °C is
performed.
No occupancy Auto-OFF
If there are no persons in the
room for the set amount of time
(60–180 minutes), the operation
is automatically stopped.
F1 F2 F3 F4
Air distribution
Select:
Cur.
M-NET address
Auto vane
Direct/Indirect setting
Direct/Indirect
Vane setting
Direct Indirect
Cooling
KRUL]RQWDOĺVZLQJ keep horizontal
Heating
keep downward GRZQZDUGĺKRUL]RQWDO
F1 F2 F3 F4
Direct/Indirect setting
: Direct
: Indirect
: Indirect
: Direct
Select:
Outlet
Angle
(QHUJ\VDYLQJRSWLRQ
F1 F2 F3 F4
Energy saving option
Cursor
Setting display:
No occupancy energy save
Room occupancy energy save
No occupancy Auto-OFF
F1 F2 F3 F4
Energy saving option
Select:
No occupancy energy save
Cooling/Heating
F1 F2 F3 F4
Energy saving option
Select:
Room occupancy energy save
Cooling/Heating
F1 F2 F3 F4
Energy saving option
Select:
Time
No occupancy Auto-OFF
120 min.
F1 F2 F3 F4
18:47 Thu
Shut down by
No Occupancy Auto-OFF
31/Dec AM12:59
2
When No occupancy energy save
or Room occupancy energy save
is selected
Select the setting with the [F4]
button.
OFF ĺ Cooling only ĺ Heating
only ĺ Cooling/Heating ĺ2))«
After changing the setting, press
the [SELECT] button to save the
setting.
OFF: The function is disabled.
Cooling only: The function is
enabled only during cooling mode.
Heating only: The function is
enabled only during heating mode.
Cooling/Heating: The function is
enabled during both cooling mode
and heating mode.
3
When No occupancy Auto-OFF is
selected
Set the time with the [F3] or [F4]
button.
ʊ 7KH VHWWLQJ LV GLVDEOHG
(the operation will not stop
automatically).
60 – 180: The time can be set in
10-minute increments.
4 The message at left will appear
if the operation was stopped
automatically by the No occupancy
Auto-OFF setting.