Mitsubishi Electric MR-J5 Series Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 316

background image

82

3 SIGNALS AND WIRING
3.7 Servo motor with an electromagnetic brake

3.7

Servo motor with an electromagnetic brake

Precautions

• For specifications such as the power supply capacity and operation delay time of the electromagnetic brake, and for

selecting the surge absorber for the electromagnetic brake, refer to the following.



Rotary Servo Motor User's Manual (HK series)

• The electromagnetic brake on the servo motor is designed to hold the motor shaft. Do not use it for normal braking.
• The electromagnetic brake may not hold the motor shaft because of incorrect wiring, its life, and mechanical structure (e.g.

when using a timing belt). To ensure safety, install a stopper on the machine side.

• If it is assumed that a hazardous situation may arise when the equipment power is off or a product malfunction occurs, use

a servo motor with an electromagnetic brake or provide an external brake system for holding purpose to prevent such
hazard.

• Configure an electromagnetic brake circuit that is interlocked with an external emergency stop switch.
• Before operating the servo motor, be sure to confirm that the electromagnetic brake operates properly.
• For the power supply of the electromagnetic brake, use the power supply designed exclusively for the electromagnetic

brake.

• If using EM2 (Forced stop 2), use MBR (Electromagnetic brake interlock) for operating the electromagnetic brake.
• If using the servo motor with the electromagnetic brake, the electromagnetic brake will operate when the power (24 V DC)

turns off.

• If using the servo motor with the electromagnetic brake, turn off the servo-on command after the servo motor stops.

Connection diagram [G] [A]

*1 Configure a circuit which interlocks with an emergency stop switch to shut off.
*2 Do not share the 24 V DC power supply for interface with the electromagnetic brake.

B1

B2

ALM

MBR

DOCOM

MBR

RA1

*1

RA1

B

*2

U

Servo amplifier

Servo motor

24 V DC

(Malfunction)

24 V DC

«
...
82
83
84
85
86
...
»

Содержание MR-J5 Series





























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MR-J5 Series

Бренд: Falco Systems Страницы: 8

Бренд: Baldwin Boxall Страницы: 4

Бренд: Yamaha Страницы: 84

Бренд: Laney Страницы: 16

Бренд: Parasound Страницы: 20

Бренд: Gibson Страницы: 1

Бренд: Interface Devices Страницы: 8

Бренд: Intelix Страницы: 12

Бренд: PS Audio Страницы: 28

Бренд: Aesthetix Страницы: 11

Two-Rock Jet Signature

Бренд: K&M Analog Designs Страницы: 7

Бренд: Fortin Страницы: 12

Бренд: Kramer Страницы: 12

Бренд: Knoll Страницы: 2

Six Channel Power Amplifier RB-956AX

Бренд: Rotel Страницы: 7

Бренд: Altimium Страницы: 36

Бренд: Soundigital Страницы: 14

Бренд: Imagine Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды