Mitsubishi Electric MR-J5 Series Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 316

background image

3 SIGNALS AND WIRING

3.5 Signal (device) explanation

61

3

Output device explanation

■

ALM (Malfunction)

If the protective circuit operates and shuts off the base circuit, ALM will turn off.
If an alarm is not occurring, ALM will turn on in 2.5 s to 3.5 s after power-on (or in 3.5 s to 4.0 s for a multi-axis servo amplifier).

■

INP (In-position)

If droop pulses are within the in-position range, INP will turn on. The in-position range can be changed with [Pr. PA10]. When
the servo motor is operated at low speed by increasing the in-position range, INP may remain on.
The device cannot be used in the velocity mode or torque mode.

■

RD (Ready)

When the servo amplifier becomes in the servo-on state, RD switches on.

Variable gain
selection 2

CDPS2









DO-1



CDPS2 (Variable
gain selection 2)

Absolute position
undetermined

ABSV









DO-1



ABSV (Absolute
position
undetermined)

During tough
drive

MTTR









DO-1



MTTR (During
tough drive)

Electromagnetic
brake interlock

MBR









DO-1



MBR
(Electromagnetic
brake interlock)

Limiting speed

VLC









DO-1



VLC (Limiting
speed)

Zero speed
detection

ZSP









DO-1



ZSP (Zero speed
detection)

Limiting torque

TLC









DO-1



TLC (Limiting
torque)

ABS
transmission
data bit 0

ABSB0









DO-1



ABSB0 (ABS
transmission
data bit 0)

ABS
transmission
data bit 1

ABSB1









DO-1



ABSB1 (ABS
transmission
data bit 1)

ABS
transmission
data ready

ABST









DO-1



ABST (ABS
transmission
data ready)

Malfunction/
Warning

ALMWNG









DO-1



ALMWNG
(Malfunction/
Warning)

AL9F warning

BW9F









DO-1



BW9F (AL9F
warning)

Device name

Symbol

Model

I/O signal
interface type

Detailed
explanation

G

A

P

S

T

«
...
61
62
63
64
65
...
»

Содержание MR-J5 Series





























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MR-J5 Series

Бренд: NAD Страницы: 4

Бренд: Hill Audio Страницы: 12

Бренд: Signal Страницы: 16

Бренд: JEFF ROWLAND Страницы: 15

Бренд: Yaesu Страницы: 18

Бренд: Parasound Страницы: 16

Claymount AmpMC 3-field Series

Бренд: Varex Imaging Страницы: 24

Бренд: PI Страницы: 43

Бренд: Bazooka Страницы: 6

Бренд: Whelen Engineering Company Страницы: 5

Бренд: audiophony Страницы: 5

Бренд: Gamut Страницы: 10

Бренд: Rane Страницы: 4

Euro Rack Classic VCA

Бренд: Oakley Sound Страницы: 7

Бренд: Phoenix Gold Страницы: 8

Бренд: AVPro Edge Страницы: 15

Бренд: GE Страницы: 14

Бренд: ADJ Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды